Samsung DC48E-M クイック設定ガイド
Quick Setup Guide
− The colour and the appearance may differ depending on the product, and the
specifications are subject to change without prior notice to improve the performance.
− Download the user manual from the website for further details.
http://www.samsung.com/displaysolutions
DC32E-M DC40E-M DC48E-M DC55E-M
DC40E-H DC48E-H
BN68-07848H-00
The terms HDMI and HDMI High-Definition Multimedia Interface,
and the HDMI Logo are trademarks or registered trademarks of
HDMI Licensing LLC in the United States and other countries.
Reverse Side
1
Connects to the audio of a source device.
2
Connects to a source device using the AV/Component adapter.
3
Receives sound from a PC via an audio cable.
4
Connect to a USB memory device.
5
DVI IN: Connects to a source device using a DVI cable or HDMI-DVI cable.
MAGICINFO IN: Use the (dedicated) DP-DVI cable when connecting a network box (sold separately).
6
Connects to a source device using an HDMI cable.
7
Supplies power to the external sensor board or receives the light sensor signal.
8
Connects to MDC using an RS232C adapter.
9
Connects to a source device using a D-SUB cable.
0
Connects to MDC using a LAN cable.
Issues
Solutions
The screen keeps
switching on and off.
Check the cable connection between
the product and PC, and ensure the
connection is secure.
No Signal is displayed
on the screen.
Check that the product is connected
correctly with a cable.
Check that the device connected to the
Check that the device connected to the
product is powered on.
Not Optimum Mode is
displayed.
This message is displayed when a signal
from the graphics card exceeds the product’s
maximum resolution and frequency.
Refer to the Standard Signal Mode Table
Refer to the Standard Signal Mode Table
and set the maximum resolution and
frequency according to the product
specifications.
The images on the
screen look distorted.
Check the cable connection to the
product.
The screen is not clear.
The screen is blurry.
Adjust Coarse and Fine.
Remove any accessories (video extension
Remove any accessories (video extension
cable, etc) and try again.
Set the resolution and frequency to the
Set the resolution and frequency to the
recommended level.
The screen appears
unstable and shaky.
Check that the resolution and frequency
of the PC and graphics card are set within
a range compatible with the product.
Then, change the screen settings if
required by referring to the Additional
Information on the product menu and the
Standard Signal Mode Table.
There are shadows or
ghost images left on
the screen.
Issues
Solutions
The screen is too bright.
The screen is too dark. Adjust Brightness and Contrast.
Screen colour is
inconsistent.
Go to Picture and adjust the Colour Space
settings.
White does not really
look white.
Go to Picture and adjust the White Balance
settings.
There is no sound.
Check the connection of the audio cable or
adjust the volume.
Check the volume.
The volume is too low. Adjust the volume.
If the volume is still low after turning
it up to the maximum level, adjust the
volume on your PC sound card or software
programme.
The remote control
does not work.
Make sure that the batteries are correctly
in place (+/-).
Check if the batteries are flat.
Check for power failure.
Make sure that the power cord is
connected.
Check for any special lighting or neon
signs switched on in the vicinity.
Troubleshooting Guide
Checking the Components
Control Panel
Contact the vendor where you purchased the product if any
components are missing.
The pictures may look different from the actual components.
The pictures may look different from the actual components.
Speaker
Speaker
DC32E-M
1
Power on the product.
If you press the button when the product is turned on, the
control menu will be displayed.
- To exit the OSD menu, press and hold the panel key for at least
one second.
2
Move to the upper or lower menu. You can also adjust the value
of an option.
3
Move to the left or right menu.
- You can adjust the volume by moving the panel key left or right
when the control menu is not displayed.
4
Remote sensor
Press a button on the remote control pointing at the sensor on
the front of the product to perform the corresponding function.
5
Spacer logo (Optional)
Do not pull on the spacer logo using force. The logo may tear or
break off.
Quick Setup Guide
Warranty card
(Not available in some locations)
MagicInfo Software
DVD
Power cord
Batteries
(Not available in some locations)
Remote Control
RS232C(IN) adapter AV/Component adapter
AUDIO adapter
DCE-M_DCE-H_India_QSG_BN68-07848H-00.indd 1
2016-03-11 1:26:48