Sony rdr-hx1010 ユーザーズマニュアル
100
TV Pause does not work.
, You are recording to the HDD or the HDD is full.
The programme position cannot be changed
from the programme position you are
recording.
from the programme position you are
recording.
, Set the TV’s input source to “TV.”
Recording does not start immediately after you
press
press
z REC.
, Operate the recorder only after “LOAD,”
“FORMAT,” or “INFOWRITE” disappears
from the front panel display.
from the front panel display.
Nothing was recorded even though you set the
timer setting correctly.
timer setting correctly.
, There was a power failure during recording.
, The recorder’s internal clock stopped due to a
power failure that lasted for more than 1 hour.
Reset the clock (page 86).
Reset the clock (page 86).
, The channel was disabled after the timer
recording was set. See “Channel Setting” on
page 82.
page 82.
, Disconnect the mains lead from the mains, and
connect it again.
, “PDC/VPS Scan Off” was selected in the
TOOLS menu (page 44).
, The programme contains copy protection signals
that restrict copying.
, Other timer setting overlapped the timer setting
, There is no DVD inside the recorder.
, There is not enough disc space for the recording.
, The recorder was in the process of DV Dubbing.
Recording does not stop immediately after you
press
press
x REC STOP.
, It will take a few seconds for the recorder to input
disc data before recording can stop.
Recording does not stop after you press
x.
, Open the remote’s cover and press x REC
STOP.
Timer recording is not complete or did not start
from the beginning.
from the beginning.
, There was a power failure during recording. If
the power recovers when there is a timer
recording, the recorder resumes recording.
Should the power failure continue for more than
1 hour, reset the clock (page 86).
recording, the recorder resumes recording.
Should the power failure continue for more than
1 hour, reset the clock (page 86).
, Other timer setting overlapped the timer setting
, Disc space was not enough.
, The PDC/VPS function is working.
Contents previously recorded were erased.
, Data that has been recorded on a DVD with a PC
will be erased from the disc when the disc is
inserted.
inserted.
, “Auto Title Erase” in the TOOLS menu (appears
when you press TOOLS while the Timer List
menu is turned on) is set to “On” (page 50).
menu is turned on) is set to “On” (page 50).
, The title was updated and recorded over
The PDC/VPS function does not operate.
, Check that the clock and date are set correctly.
, Check that the PDC/VPS time you set is the
correct one (there might be a mistake in the TV
programme guide). If the broadcast you wanted
to record did not send the good PDC/VPS
information, the recorder will not start recording.
programme guide). If the broadcast you wanted
to record did not send the good PDC/VPS
information, the recorder will not start recording.
, If the reception is poor, the PDC/VPS signal
might be altered and the recorder might not start
recording.
recording.
, “PDC/VPS Scan Off” is selected (page 44).
Nothing was recorded even though you set the
Synchro-Rec setting correctly.
Synchro-Rec setting correctly.
, You forgot to turn off the connected equipment.
, The recorder was not set to the Synchro-
Recording standby mode. Press SYNCHRO
REC to have the recorder stand by for recording.
Make sure the SYNCHRO REC indicator lights
up on the front panel (page 50).
REC to have the recorder stand by for recording.
Make sure the SYNCHRO REC indicator lights
up on the front panel (page 50).
, The recorder is connected to the TV output jack
of the connected equipment.
Recording/Timer recording/
Editing
Editing
Recording from the equipment
with a timer
with a timer