Sony SNCCX600 ユーザーズマニュアル
Ad
minis
minis
tra
ting t
he Camer
a
Setting the Camera tampering detection/Motion detection — Action input Menu
42
Motion detection: The alarm is triggered by the motion
detection function.
VMF: The alarm is triggered by the VMF function.
Face detection: The alarm is triggered by the face
Face detection: The alarm is triggered by the face
detection function.
Network disconnection: The alarm is triggered by
disconnection to a specific IP address.
Presence sensor: The alarm is triggered by the presence
sensor function.
Note
You cannot set Camera tampering detection and
Network disconnection in the same event condition.
Network disconnection in the same event condition.
Interval
Specify the interval time used when condition is set to
and, then.
In the case the condition is set as 1 and 2, the system
sounds an alarm when either 1 or 2 happens, and the
other happens within the specified interval.
In the case the condition is set as 1 then 2, the system
sounds an alarm when 1 happens, and then 2 happens
within the specified interval.
If you select “or” condition, this setting will be ignored.
The maximum duration to be set is 7200 seconds.
and, then.
In the case the condition is set as 1 and 2, the system
sounds an alarm when either 1 or 2 happens, and the
other happens within the specified interval.
In the case the condition is set as 1 then 2, the system
sounds an alarm when 1 happens, and then 2 happens
within the specified interval.
If you select “or” condition, this setting will be ignored.
The maximum duration to be set is 7200 seconds.
Camera tampering detection Tab —
Set the camera tampering detection
Set the camera tampering detection
Notes
• Before using the camera tampering detection function,
adjust the image first.
If you adjust focus/zoom with the camera tampering
detection function activated, detection may not be
effective.
If you adjust focus/zoom with the camera tampering
detection function activated, detection may not be
effective.
• Deselect the checkbox of Stabilizer in the Installation
tab of the System menu. After setting the camera
tampering detection, set the Stabilizer function again.
tampering detection, set the Stabilizer function again.
Enable
Select the checkbox to activate the function to detect
camera tampering, such as direction shifting or spray.
camera tampering, such as direction shifting or spray.
Detection status
Display the tampering detection state of the time when
Camera tampering detection tab is opened. To clear the
detection status, click Clear button.
Camera tampering detection tab is opened. To clear the
detection status, click Clear button.
OK/Cancel
Motion detection Tab — Set the
motion/VMF detection
motion/VMF detection
Motion detection responds to moving objects in the
camera image and triggers an alarm.
In VMF, an alarm sounds when motion is detected under
the motion detection setting, entering or passing through
a specified area or inspection line. An alarm also sounds
when an object has been left or removed from a specified
area or inspection line.
The detected object will be displayed on the monitor in
the green frame. The removed object and left object will
be displayed in the magenta frame.
When you click the Motion detection tab, a dialog
appears. Enter the user name and password.
The factory setting of the user name and password for
the Administrator is set to “admin”.
Change the password from the factory setting for the
security of your devices.
camera image and triggers an alarm.
In VMF, an alarm sounds when motion is detected under
the motion detection setting, entering or passing through
a specified area or inspection line. An alarm also sounds
when an object has been left or removed from a specified
area or inspection line.
The detected object will be displayed on the monitor in
the green frame. The removed object and left object will
be displayed in the magenta frame.
When you click the Motion detection tab, a dialog
appears. Enter the user name and password.
The factory setting of the user name and password for
the Administrator is set to “admin”.
Change the password from the factory setting for the
security of your devices.
Note
Perform the following before setting the motion
detection.
• Set Image size1 in the Video codec tab of the Video /
detection.
• Set Image size1 in the Video codec tab of the Video /
Audio menu to the maximum rate.
• Deselect the checkbox of Image 1 in the PTZ control
tab of the PTZ control menu.
• Deselect the checkbox of Stabilizer in the Installation
tab of the System menu.
What is VMF
VMF is a function for detecting an object entering or
passing through a specified area or inspection line, or
when an object has been left or removed from a specified
area or inspection line. Video/audio recording and/or
audio file playback can be synchronized with this alarm.
You can set the inspection methods to execute
independently. Intrusion and Passing can also be set to
execute in combination.
For example:
• An alarm sounds when an object enters areas A, B and
passing through a specified area or inspection line, or
when an object has been left or removed from a specified
area or inspection line. Video/audio recording and/or
audio file playback can be synchronized with this alarm.
You can set the inspection methods to execute
independently. Intrusion and Passing can also be set to
execute in combination.
For example:
• An alarm sounds when an object enters areas A, B and
C.
• An alarm sounds when an object passes through area
A and enters area B.
• An alarm sounds when an object passes through areas
A and B, and enters area C.
• An alarm sounds when an object enters area A, and
passes through area B.
Intrusion
When a moving object enters the designated area, an
alarm sounds.
alarm sounds.