Sony STR-DH810 ユーザーズマニュアル
80
GB
Tip
The “LARGE” and “SMALL” settings for each
speaker determine whether the internal sound
processor will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the subwoofer or other “LARGE”
speakers.
However, since bass sounds have a certain amount of
directionality, it is best not to cut them, if possible.
Therefore, even when using small speakers, you can
set them to “LARGE” if you want to output the bass
frequencies from that speaker. On the other hand, if
you are using a large speaker, but prefer not to have
bass frequencies output from that speaker, set it to
“SMALL”.
If the overall sound level is lower than you prefer, set
all speakers to “LARGE”. If there is not enough
bass, you can use the equalizer to boost the bass
levels. For details, see page 81.
speaker determine whether the internal sound
processor will cut the bass signal from that channel.
When the bass is cut from a channel, the bass
redirection circuitry sends the corresponding bass
frequencies to the subwoofer or other “LARGE”
speakers.
However, since bass sounds have a certain amount of
directionality, it is best not to cut them, if possible.
Therefore, even when using small speakers, you can
set them to “LARGE” if you want to output the bass
frequencies from that speaker. On the other hand, if
you are using a large speaker, but prefer not to have
bass frequencies output from that speaker, set it to
“SMALL”.
If the overall sound level is lower than you prefer, set
all speakers to “LARGE”. If there is not enough
bass, you can use the equalizer to boost the bass
levels. For details, see page 81.
x SB ASSIGN
• SPK B
If you connect an additional front speaker
system to the SPEAKERS SURROUND
BACK/FRONT HIGH/BI-AMP/FRONT B
terminals, select “SPK B”.
system to the SPEAKERS SURROUND
BACK/FRONT HIGH/BI-AMP/FRONT B
terminals, select “SPK B”.
• BI-AMP
If you connect front speakers to the
SPEAKERS SURROUND BACK/FRONT
HIGH/BI-AMP/FRONT B terminals using a
bi-amplifier connection, select “BI-AMP”.
SPEAKERS SURROUND BACK/FRONT
HIGH/BI-AMP/FRONT B terminals using a
bi-amplifier connection, select “BI-AMP”.
• OFF
If you connect surround back speakers or
front high speakers to the SPEAKERS
SURROUND BACK/FRONT HIGH/
front high speakers to the SPEAKERS
SURROUND BACK/FRONT HIGH/
BI-AMP/FRONT B terminals, select “OFF”.
Note
When you change the connection from bi-amplifier
or speaker front B to surround back or front high
speakers connection, set “SB ASSIGN” to “OFF”,
then perform the Auto Calibration again (page 37).
or speaker front B to surround back or front high
speakers connection, set “SB ASSIGN” to “OFF”,
then perform the Auto Calibration again (page 37).
x FL DIST.
x FR DIST.
Lets you set the distance from your listening
position to the front speakers.
If both front speakers are not placed an equal
distance from your listening position, set the
distance to the closest speaker.
position to the front speakers.
If both front speakers are not placed an equal
distance from your listening position, set the
distance to the closest speaker.
x CNT DIST.
Lets you set the distance from your listening
position to the center speaker.
position to the center speaker.
x SL DIST.
x SR DIST.
Lets you set the distance from your listening
position to the surround speakers.
position to the surround speakers.
x SB DIST.
x SBL DIST.
x SBR DIST.
Lets you set the distance from your listening
position to the surround back speakers.
position to the surround back speakers.
x LH DIST.
x RH DIST.
Lets you set the distance from your listening
position to the front high speakers.
position to the front high speakers.
x SW DIST.
Lets you set the distance from your listening
position to the subwoofer.
position to the subwoofer.
Notes
• Depending on the speaker pattern setting. Some
parameters may not be available.
• This function does not work in the following cases.
– Signals with a sampling frequency of more than
96 kHz are being received.
– Analog Direct is selected.