Panasonic GR-DX75 ユーザーズマニュアル
EN
14
12 : 34 : 24
TAPE RECORDING
Time Code
During recording, a time code is recorded on the tape.
This code is to confirm the location of the recorded
scene on the tape during playback.
If recording starts from a blank portion, the time code
begins counting from “00:00:00” (minute:second:frame).
If recording starts from the end of a previously recorded
scene, the time code continues from the last time code
number.
This code is to confirm the location of the recorded
scene on the tape during playback.
If recording starts from a blank portion, the time code
begins counting from “00:00:00” (minute:second:frame).
If recording starts from the end of a previously recorded
scene, the time code continues from the last time code
number.
To perform Random Assemble Editing (
墌
pg. 41 – 43),
time code is necessary. If during recording a blank
portion is left partway through the tape, the time code
is interrupted. When recording is resumed, the time
code starts counting up again from “00:00:00”. This
means the camcorder may record the same time codes
as those existing in a previously recorded scene. To
prevent this, perform “RECORDING FROM THE
MIDDLE OF A TAPE” in the following cases;
portion is left partway through the tape, the time code
is interrupted. When recording is resumed, the time
code starts counting up again from “00:00:00”. This
means the camcorder may record the same time codes
as those existing in a previously recorded scene. To
prevent this, perform “RECORDING FROM THE
MIDDLE OF A TAPE” in the following cases;
• When shooting again after playing back a recorded
tape.
• When power shuts off during shooting.
• When a tape is removed and re-inserted during
• When a tape is removed and re-inserted during
shooting.
• When shooting using a partially recorded tape.
• When shooting on a blank portion located partway
• When shooting on a blank portion located partway
through the tape.
• When shooting again after shooting a scene then
opening/closing the cassette holder cover.
RECORDING FROM THE MIDDLE OF A TAPE
1
Play back a tape or use Blank Search (
墌
pg. 15) to
find the spot at which you want to start recording, then
engage the Still Playback mode (
engage the Still Playback mode (
墌
pg. 14, “Normal
Playback”).
2
Set the Power Switch
@
to “
” or “
” while
pressing down the Lock Button
$
located on the
switch, then start recording.
NOTES:
● The time code cannot be reset.
● During fast-forwarding and rewinding, the time code
indication does not move smoothly.
● The time code is displayed only when “TIME CODE” is
set to “ON” (
墌
pg. 35).
Frames
(25 frames = 1 second)
(25 frames = 1 second)
Seconds
Minutes
Frames are not displayed
during recording.
during recording.
Normal Playback
1
Load a tape (
墌
pg. 9).
2
Set the VIDEO/MEMORY Switch
t
to “VIDEO”,
then set the Power Switch
@
to “
” while pressing
down the Lock Button
$
located on the switch. To start
playback, press 4/6
!
.
• To stop playback temporarily (Still Playback), press
4
/6
!
.
• To stop playback, press 5
7
.
• Turn the SHUTTLE SEARCH Ring
#
counterclockwise (2) and release to rewind, or
clockwise (3) and release to fast-forward the tape
during Stop mode.
clockwise (3) and release to fast-forward the tape
during Stop mode.
• High-speed picture search (Shuttle Search) is
possible by turning the SHUTTLE SEARCH Ring
#
counterclockwise (2) or clockwise (3) during
playback (holding the SHUTTLE SEARCH Ring
playback (holding the SHUTTLE SEARCH Ring
#
continues search until released).
• Press the Zoom Button T
Y
on the remote control to
zoom in (up to 44X*/50X**), or W
T
to zoom out. You
can also magnify a particular part of an image
(
(
墌
pg. 39).
* GR-DX95/DX75 only
**GR-DX300/DX100 only
**GR-DX300/DX100 only
• At any time, pressing 4/6
!
resumes normal
playback.
Slow-Motion Playback/Playback Special Effects/
Playback Zoom:
Available only with the remote control (
Playback Zoom:
Available only with the remote control (
墌
pg. 39)
To Control The Speaker Volume:
..... press VOL. +
e
to turn up the volume, or –
w
to
turn down the volume.
ATTENTION
During Shuttle Search, parts
of the picture may not be
clearly visible, particularly on
the left side of the screen.
of the picture may not be
clearly visible, particularly on
the left side of the screen.
TAPE PLAYBACK
Display
01 DX300/100/95/75EK_EN 12-16
2/26/03, 7:12 PM
14