Panasonic SC-HT930 ユーザーズマニュアル
5
RQT7972
[HT930]
1
Assemble the speaker stands.
1
Thread the speaker cable through the base.
For quicker threading, loosely fold the cable in half (do not
crease), pass the folded portion through the hole, and then pull
the rest of the cable through the base.
For quicker threading, loosely fold the cable in half (do not
crease), pass the folded portion through the hole, and then pull
the rest of the cable through the base.
2
Insert the pipe.
3
Secure the pipe to the base.
Ensure the screws are securely fastened.
Ensure the screws are securely fastened.
2
Attach the stands to the speakers.
Ensure the stand is fastened on straight by gradually tightening the
top and bottom screws alternately until fully tightened.
top and bottom screws alternately until fully tightened.
You can also attach to the lower rear of the speaker.
The height of the speaker can be changed when attaching the
stand to the upper rear or lower rear of the speaker.
The height of the speaker can be changed when attaching the
stand to the upper rear or lower rear of the speaker.
3
Connect the speaker cables.
4
Secure the speaker cables to the bases.
∫ Preventing the speakers from falling over
[HT730]
[HT930]
Preparation
Attach screw eyes (not included) to secure the speakers to the
wall (‹ diagram right).
Attach screw eyes (not included) to secure the speakers to the
wall (‹ diagram right).
≥You will need to obtain the appropriate screw eyes to match
the walls or pillars to which they are going to be fastened.
≥Consult a qualified housing contractor concerning the
appropriate procedure when attaching to a concrete wall or a
surface that may not have strong enough support. Improper
attachment may result in damage to the wall or speakers.
surface that may not have strong enough support. Improper
attachment may result in damage to the wall or speakers.
1
Thread the string (not included) through the slot on the
rear of the speaker to prevent it from falling over.
rear of the speaker to prevent it from falling over.
2
Loop the string through the screw eye and tie tightly.
2 Front speakers
2 Bases
2 Pipes
4 Short screws
4 Long screws
Cable
Base
Leave the excess speaker
cable for connecting later.
cable for connecting later.
Plastic wrap
Insert the pipe while gently
pulling on the speaker cable.
pulling on the speaker cable.
Match these holes when you insert
the pipe.
the pipe.
Pipe support
Pipe
Base
Short screws
Phillips-head screwdriver
(not included)
(not included)
Before proceeding to the next step, please remove the plastic
wrap from the pipe.
wrap from the pipe.
Front speaker
Long screws
Pipe
Twist off the vinyl ends of the
speaker cables.
speaker cables.
Rear of the speaker
_:
Copper
`:
Silver
Push!
If there is any excess speaker cable, thread the speaker cable
into the opening near the top of the pipe while pulling the speaker
cable from the bottom of the base.
into the opening near the top of the pipe while pulling the speaker
cable from the bottom of the base.
Press the speaker cable into the
groove.
groove.
Rear side
of base
of base
Press the speaker cable into
the base cover groove as far
as possible.
the base cover groove as far
as possible.
Cable
Groove
String (not included)
Wall
Screw eye (not included)
Rear of the speaker
Approx. 150 mm (5
29
/
32
z)
[HT730]
[HT930]
String (not included)
Wall
Screw eye (not included)
Rear of the speaker
Approx. 150 mm (5
29
/
32
z)
F
ron
t spe
a
k
e
r as
semb
ly
[Note]
To prevent the speaker cables from being pulled out of the pipes, leave the plastic wrap on the pipes while
assembling the speaker stands.
assembling the speaker stands.
7972en-p03-27.fm 5 ページ ２００４年１２月１０日 金曜日 午後６時３８分