Panasonic wj-sx650p ユーザーズマニュアル
38
Before operation, setup of this unit is required. Setup is per-
formed from WJ-SX650 Series Administrator Console installed
on a PC. (Some settings are available from SETUP MENU of
this unit.) The following is an example of setup procedure.
formed from WJ-SX650 Series Administrator Console installed
on a PC. (Some settings are available from SETUP MENU of
this unit.) The following is an example of setup procedure.
Notes:
• Setup may differ depending on system composition.
(Settings of Step 1 and 4 in the following procedure
must be performed.)
must be performed.)
• For Step 2, 3, 5 and 6 in the following setup procedure,
the factory default can be maintained.
Example: camera x 150, recorder x 10, monitor x 32, and
system controller x 2 (Terminal mode)
1. Perform the recorder settings.
Recorder Out: Matrix Input
Input Board No.: 5 (When video input signals are sup-
Input Board No.: 5 (When video input signals are sup-
plied from recorders to CAM 160 to 151)
Recorder 1 to 10: ON
Recorder 11 to 16: OFF
Recorder 11 to 16: OFF
Note: Check if recorders are properly connected to the
DATA port and CAM (CAMERA IN connectors) currently
displayed.
displayed.
<To perform settings in WJ-SX650 Series Administrator
Console>
"System" – "Recorder"
Console>
"System" – "Recorder"
<To perform settings in SETUP MENU>
RECORDER (Refer to p. 50.)
RECORDER (Refer to p. 50.)
2. Perform the DATA port settings. (In this example, main-
tain the factory default.)
DATA 1, 2, 5 and 6 ports: TMNL
DATA 3, 4, 7 and 8 ports: HDR
DATA 1, 2, 5 and 6 ports: TMNL
DATA 3, 4, 7 and 8 ports: HDR
Note: Change these parameters when using PS·Data
system controllers, etc.
<To perform settings in WJ-SX650 Series Administrator
Console>
"System" – "DATA Port"
Console>
"System" – "DATA Port"
<To perform settings in SETUP MENU>
DATA PORT (Refer to p. 52.)
DATA PORT (Refer to p. 52.)
3. Perform the LCN (Logical Camera Number) settings.
CAM001 to 160: If you change LCN settings, select
desired parameters.
CAM161 to 256: Delete the LCN parameters.
Notes:
• Set LCN parameters for CAM151 to 160 surely, even
though these channels accept video input signals from
recorders. Without LCN settings, recorder selection is
unavailable.
recorders. Without LCN settings, recorder selection is
unavailable.
• By deleting the LCN parameters of unused camera
input channels, operators can select only existing cam-
era numbers.
era numbers.
<To perform settings in WJ-SX650 Series Administrator
Console>
"System" – "Logical Camera Number"
Console>
"System" – "Logical Camera Number"
<To perform settings in SETUP MENU>
Not available
Not available
4. Perform the camera settings.
CAM001 to 150: Select desired parameters for these
cameras. (To use cameras of other manufacturers,
set VD2 and DATA to OFF.) For Cable (cable com-
pensation), select the parameter suited to the cable
length.
set VD2 and DATA to OFF.) For Cable (cable com-
pensation), select the parameter suited to the cable
length.
CAM151 to 160: Set VD2 and DATA to OFF. (Video input
signals are supplied from recorders to these channels.)
<To perform settings in WJ-SX650 Series Administrator
Console>
"System" – "VD2/DATA/Cable Comp."
Console>
"System" – "VD2/DATA/Cable Comp."
Setup Procedure