JVC CA-UXF3B ユーザーズマニュアル

0410YOMMDWCDT

©2010 Victor Company of Japan, Limited

LVT2121-017A[A/UJ]

DEMO
DEMO OFF

DIM 1

DIM 2

DIM OFF

TURBO ON
TURBOOFF

HBS ON
HBS OFF

ROCK

POP

CLASSIC

JAZZ

FLAT

SLEEP 10

SLEEP 20

SLEEP 30

SLEEPOFF

• • •

SLEEP180

DAILY 1

DAILY 2

DAILY 3

Thank you for purchasing a JVC product.

ASTB ON
ASTB OFF

You can dim the display window and illumination.

You can change the information shown on the 
display.

Ex.: During playback of a CD...

The information shown on the display differs 
depending on the source.
Tag information is shown on the display while an 
MP3/WMA file is played back.

❍

•

•

To drop the volume in a moment

To restore the volume, press again or adjust the 
volume level.

To emphasize the sound

To reinforce the bass sound

To select the sound mode suitable for your favorite 
music

❍

•

If you have already set the clock before, press and 
hold CLOCK/TIMER until the current time is shown 
on the display then press SET to activate the clock 
setting mode.

To go back to the previous step, press MENU/
CANCEL.

The clock may gain or lose 1 to 2 minutes per month. 
You may need to readjust the clock periodically.

•

•

•

When you go away for an extended period of time, 
remove the plug from the wall outlet.
When unplugging the System from the wall outlet, 
always pull the plug, not the power cord.
Do not handle the power cord with wet hands.
Disconnect the power cord before cleaning the System or 
moving the System.
Do not alter, twist or pull the power cord, or put anything 
heavy on it, which may cause fire, electric shock, or other 
accidents.

Do not place the System in moist or dusty places.
If water gets inside the System, turn off the power and 
remove the plug from the wall outlet, then consult your 
dealer. Using the System in this state may cause a fire or 
electrical shock.
Do not expose the System to direct sunlight or place it 
near a heating device.

•

•

•
•

•

•
•

•

Lithium coin battery
(product number: 
CR2025)

For better FM reception
Disconnect the supplied FM antenna, and connect to an outdoor FM antenna 
(not supplied) using a 75 Ω wire with coaxial type connector (IEC or DIN45325).

To a wall outlet

FM antenna (supplied): Extend it so that you can obtain the best reception.

To get the best performance of the System, keep your discs 
and the mechanism clean.

Remove the disc from its case by holding it at the edge 
while pressing the center hole lightly.
Do not touch the shiny surface of the disc, or bend the 
disc.
Put the disc back in its case after use.
Be careful not to scratch the surface of the disc when 
placing it back in its case.
Avoid exposure to direct sunlight, temperature extremes, 
and moisture.

Wipe the disc with a soft cloth in a straight line from 
center to edge.

Stains should be wiped off with a soft cloth. If the System 
is heavily stained, wipe it with a cloth soaked in water-
diluted neutral detergent and wrung well, then wipe 
clean with a dry cloth.
Since the System may deteriorate in quality, become 
damaged or get its paint peeled off, be careful about the 
following:

DO NOT wipe it hard.
DO NOT wipe it with thinner or benzine.
DO NOT apply any volatile substances such as 
insecticides to it.
DO NOT allow any rubber or plastic to remain in contact 
for a long time.

•

•

•
•

•

•

•

•

–
–
–

–

Make sure the antenna conductors do not touch any other terminals, connecting cords or the power cord. Also, keep the antennas away 
from metallic parts of the System, connecting cords, and the AC power cord. Otherwise, it could cause poor reception.
When connecting the speaker cords, match the polarities of the speaker terminals: red to (+) and black to (–).
DO NOT connect more than one speaker to each terminal.
Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the System.
DO NOT allow the conductor of the speaker cords to come into contact with the metallic parts of the System.

•

•
•
•
•

Select a place which is level, dry and neither too hot nor 
too cold—between 5˚C and 35˚C.
Do not install the System in a place subject to vibrations.
Do not put heavy objects on the System.

Do not insert any metallic objects, such as wires, hairpins, 
coins, etc. into the System.
Do not block the vents.

•

•
•

•

•

For turning off the demonstration display, see 
“Canceling the display demonstration” in “Initial 
settings.”

This System can play back...

Audio CD and CD-R/CD-RW in Audio CD format
MP3/WMA files on a CD-R/CD-RW (ISO 9660 format), 
USB mass storage class device (maximum data transfer 
rate: 2 Mbps).

This System cannot play “packet write” discs.
This System can recognize up to 255 groups on a disc. 
The total number of groups and tracks (on a disc) that can 
be recognized by the System is 512 (for MP3/WMA).
This System can recognize up to 99 groups and 999 tracks 
(with a maximum number of 255 tracks in a group) on a 
USB mass storage class device.
For MP3/WMA playback...

Some MP3/WMA files may not be played back due to 
their recording conditions.
This System can play only discs of ISO 9660 Level 1 or 
Level 2.
It is recommended to record each file at a sampling rate 
of 44.1 kHz and at a data transfer rate of 128 kbps.
This System cannot play back files made at a bit rate of 
less than 64 kbps.
This System can show the Tag data (Version 1).

For playback of files on a USB mass storage class device.

You cannot play back files larger than 2 GB.
This System may not play back some USB mass storage 
class devices and does not support DRM (Digital Rights 
Management).

About SCMS (Serial Copy Management System)
The System uses the Serial Copy Management System 
which allows only first-generation digital copies to be 
made of premastered software such as regular CDs.
If you try to record from a duplicated CD-R or CD-RW to a 
USB mass storage class device, “PROTECT” appears on the 
display.

•

–
–

•
•

•

•

–

–

–

–

–

•

–
–

When you use the remote control for the first time, pull out the insulation sheet.

❍

After unpacking, check to make sure that you have all the 
following items:

Remote control (× 1)
Lithium coin battery CR2025 (× 1)

The battery has been installed in the remote control when 
shipped from the factory.

FM antenna (× 1)
AC plug adaptor (× 1) (Not supplied for Australian model.)

If anything is missing, consult your dealer immediately.

❍

•
•

–

•
•

Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor immediately.
To prevent the battery from overheating, cracking, or starting a fire:

Do not recharge, short, disassemble or heat the battery or dispose of it in a fire.
Do not leave the battery with other metallic materials.
Wrap the battery with tape and insulate when throwing away or saving it.
Do not poke the battery with tweezers or similar tools.

Dispose of battery in the proper manner, according to federal, state, and local regulations.
The battery (battery pack or battery installed) shall not be exposed to excessive heat source such as sunshine, fire or the like.

•
•

–
–
–
–

•
•

CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

General
Power source:

For Australian model: 

AC 240 V   , 50 Hz

For another model: 

AC 110 V – 127 V / 220 V – 240 V 

 

adjustable with voltage selector, 50/60 Hz

Power consumption (at operation): 

40 W

Power consumption (on standby): 

1.00 W or less

Dimensions (approx.) (W x H x D) (including projecting 
parts): 

236 mm × 123 mm × 285 mm 

Mass (approx.): 

2.0 kg

Amplifier
Output Power: 

60 W (30 W + 30 W) at 6 Ω (10% THD)

Audio Input: 

AUDIO IN: Stereo mini (ø 3.5 mm)

Speaker impedance: 

6 Ω - 16 Ω

Tuner
FM frequency: 

87.50 MHz – 108.00 MHz

USB
USB specification: 

Compatible with USB 2.0 Full Speed

Compatible device: 

Mass storage class

Compatible system: 

FAT16, FAT32

Output power: 

DC 5 V 

 500 mA

iPod
Output power: 

DC 5 V 

 500 mA

Video out: 

Composite

Speaker(SP-UXF3B)
Speaker type: 

Bass-reflex type

Tweeter: 4 

cm

Woofer: 12 

cm

Impedance: 6 

Ω 

Dimensions (approx.) (W x H x D) (including projecting 
parts): 

141 mm × 250 mm × 181 mm

Mass (approx.): 

1.8 kg each

Supplied accessories
See “Supplied accessories” in “Getting started.”

Red

Black

From left speaker

From right speaker

Red

Black

If the System does not work correctly, disconnect the AC power cord from the wall outlet, wait for a while, and 
connect the cord again.
JVC bears no responsibility for any loss of data in USB mass storage class device while using this System.

•

•

If you are having a problem with your System, check this list for a possible solution before calling for service.

The timer indicator is turned off.

You can turn off the System automatically.

The A.STBY indicator starts flashing after playback 
stops. If no operation is done for about 3 minutes, the 
System is turned off. 
This function cannot be used when “TUNER FM” or 
“AUDIO IN” is selected as the source.

•

•

Specify the time (in minutes.)

To check the remaining time until the System shuts off, 
press SLEEP once.

By using Daily Timer, you can wake up with your favorite 
music.

You can store three Daily Timer settings.
Tune into a station, insert a disc or connect a USB mass 
storage class device/iPod to the System beforehand.

Hour and minute for the on-time and off-time
Playback source
Volume

If you select “VOL – –,” the volume is set to the 
same level as when the System was last turned off.

To correct a misentry during the process, press 
MENU/CANCEL. You can return to the previous step.
To exit from Daily Timer setting, press 
CLOCK/TIMER repeatedly as required.

The display disappears and the STANDBY lamp starts 
flashing.

While on standby mode, the timer indicator (   ) is 
not displayed.

•

•
•

–
–
–

•

•

•

•

❍

Power does not come on.

\  Power plug is not inserted securely. Plug it in securely.

Adjustments or settings are 
suddenly canceled before you finish.

\  There is a time limit. Start the procedure again.

Unable to operate the System from 
the remote control.

\  The path between the remote control and the remote sensor on the System is 

blocked.

\  The battery is exhausted.

No sound is heard.

\  Speaker connections are incorrect or loose.

\  Headphones are connected.

Hard to listen to broadcasts because 
of noise.

\  Antenna connection is incorrect or loose.

\  The FM antenna is not properly extended and positioned.

\  Electrostatic discharge from your body may cause noise. If this happens, turn 

the System off then on again.

iPod
The iPod does not play, but 
“CONNECT” appears on the display.

\  The iPod battery is low or exhausted. Charge the iPod battery.

The disc/USB mass storage class 
device does not play.

\  The disc is placed upside down. Place the disc with the label side facing up.

\  The disc is recorded using “packet writing (UDF file system).” It cannot be 

played.

\  The USB mass storage class device is not connected properly.

“NO DATA” appears on the display. 

\  MP3/WMA files are not recorded on the disc, on the USB mass storage class 

device.

ID3 Tag on an MP3 file cannot be 
shown.

\  There are two types of ID3 Tag—Version 1 and Version 2. This System can only 

show ID3 Tag Version 1.

Groups and tracks are not played 
back as you expect.

\  Playing order is determined when the groups and tracks are recorded. It 

depends on the writing application.

The disc/USB mass storage class 
device sound is discontinuous.

\  The disc is scratched or dirty.

\  MP3/WMA files have not been properly recorded on the USB mass storage 

class device.

Sound from the USB mass storage 
class device is interrupted.

\  Noise and static electricity may stop the sound. In this case, disconnect and 

connect the USB mass storage class device again after turning off the System.

The disc tray does not open or close.

\  The AC power cord is not plugged in.

\  Disc ejection is prohibited. “LOCKED” appears (see “Prohibiting disc ejection” 

in “Disc/USB” on page 2).

Daily Timer does not work.

\  The System was turned on when the on-time came. The timer starts working 

only when the System is turned off.

When you plug in and turn on the System, the display 
demonstration starts automatically if no operation is 
done for about 2 minutes.

(On the main unit)

(Hold)

The remote control buttons are used for explaining the 
operations unless mentioned otherwise. However, if the 
System has the same or similar button names, they can also 
be used for the operations.
“File” and “track” are used interchangeably.

•

•

Main unit

Speaker

Speaker

Main unit

1st generation

2nd generation

Normal display

Microsoft and Windows Media are either registered 
trademarks or trademarks of Microsoft Corporation in 
the United States and/or other countries.
iPod is a trademark of Apple Inc., registered in the U.S. 
and other countries.
“Made for iPod” means that an electronic accessory 
has been designed to connect specifically to iPod and 
has been certified by the developer to meet Apple 
performance standards.
Apple is not responsible for the operation of this 
device or its compliance with safety and regulatory 
standards.

•

•

•

•

Current track’s elapsed time

Clock

(Canceled)

CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, 
and to prevent damage, locate the 
apparatus as follows:

Front: No obstructions and open 
spacing.
Sides/Top/Back: No obstructions 
should be placed in the areas 
indicated by the dimensions in the 
illustration.
Bottom: Place on the level surface. 
Maintain an adequate air path for 
ventilation by placing on a stand 
with a height of 10 cm or more.

1.

2.

3.

Monitor

Composite video cord 
(not supplied)

To composite 
video input

iPod nano 

–

iPod nano (2nd Generation)

–

iPod nano (3rd Generation)

iPod nano (4th Generation)

iPod nano (5th Generation)

iPod mini

–

iPod mini (2nd Generation)

–

iPod (4th Generation)

–

iPod classic

iPod photo (4th Generation)

 *

iPod video (5th Generation)

iPod touch

iPod touch (2nd Generation and Fall ‘09)

Only for still picture

If iPod does not play correctly, update iPod software to the 
latest version.

For details about updating iPod, check on the Apple web 
site <http://www.apple.com>.

*

•

(Hold)

CAUTION for mains (AC) line
BEFORE PLUGGING IN, do check that your mains (AC) line voltage 
corresponds with the position of the voltage selector switch provided 
on the outside of this equipment and, if different, reset the voltage 
selector switch, to prevent from a damage or risk of fire/electric 
shock.

If the wall outlet does not match the AC plug, use the supplied AC plug adaptor.
(Not supplied for Australian model.)

DIGITAL

DIGITAL

DIGITAL

ANALOG

EN_UXF3B[AUJ]4th.indd   1

EN_UXF3B[AUJ]4th.indd   1

10.5.24   4:18:14 PM

10.5.24   4:18:14 PM