JVC CA-UXF4VB ユーザーズマニュアル

LVT2123-029A[US/UX/UG/UW]

CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:

Front: No obstructions and open spacing.
Sides/Top/Back: No obstructions should be placed in the areas indicated by the dimensions in 
the illustration.
Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a 
stand with a height of 10 cm or more.

1.
2.

3.

When you plug in and turn on the System, the display 
demonstration starts automatically if no operation is done 
for about 2 minutes.

When you use the remote control for the first time, pull out the insulation sheet.

❍

After unpacking, check to make sure that you have all 
the following items:

Remote control (× 1)
Lithium coin battery CR2025 (× 1)

The battery has been installed in the remote 
control when shipped from the factory.

FM antenna (× 1)
AM loop antenna (× 1)
Composite video cord (× 1)
AC plug adaptor (× 1)
(not supplied for Middle Eastern and Saudi Arabian 
models)

If anything is missing, consult your dealer immediately.

❍

•
•

–

•
•
•
•

Lithium coin battery
(product number: CR2025)

Store the battery in a place where children cannot reach. If a child accidentally swallows the battery, consult a doctor 
immediately.
To prevent the battery from overheating, cracking, or starting a fire:

Do not recharge, short, disassemble or heat the battery or dispose of it in a fire.
Do not leave the battery with other metallic materials.
Wrap the battery with tape and insulate when throwing away or saving it.
Do not poke the battery with tweezers or similar tools.

Dispose of battery in the proper manner, according to federal, state, and local regulations.
The battery (battery pack or battery installed) shall not be exposed to excessive heat source such as sunshine, fire or 
the like.

•

•

–
–
–
–

•
•

For better FM reception
Disconnect the supplied FM antenna, and connect to an outdoor FM antenna 
(not supplied) using a 75 Ω wire with coaxial type connector.

CAUTION:
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

FM antenna (supplied): Extend it so that you can obtain the best reception.

When you go away for an extended period of time, 
remove the plug from the wall outlet.
When unplugging the System from the wall outlet, 
always pull the plug, not the power cord.
Do not handle the power cord with wet hands.
Disconnect the power cord before cleaning the System or 
moving the System.
Do not alter, twist or pull the power cord, or put anything 
heavy on it, which may cause fire, electric shock, or other 
accidents.

Do not place the System in moist or dusty places.
If water gets inside the System, turn off the power and 
remove the plug from the wall outlet, then consult your 
dealer. Using the System in this state may cause a fire or 
electrical shock.
Do not expose the System to direct sunlight or place it 
near a heating device.

Select a place which is level, dry and neither too hot nor 
too cold—between 5˚C and 35˚C.
Do not install the System in a place subject to vibrations.
Do not put heavy objects on the System.

Do not insert any metallic objects, such as wires, hairpins, 
coins, etc. into the System.
Do not block the vents.

•

•

•
•

•

•
•

•

•

•
•

•

•

Make sure the antenna conductors do not touch any other terminals, connecting cords or the power cord. Also, keep the antennas away from metallic parts of the System, 
connecting cords, and the AC power cord. Otherwise, it could cause poor reception.
When connecting the speaker cords, match the polarities of the speaker terminals: red to (+) and black to (–).
DO NOT connect more than one speaker to each terminal.
Use only speakers with the same speaker impedance as indicated by the speaker terminals on the rear of the System.
DO NOT allow the conductor of the speaker cords to come into contact with the metallic parts of the System.
The speakers are magnetically shielded to avoid color distortions on TVs. However, if not installed properly, it may cause color distortions. Therefore, pay attention to the following 
when installing the speakers.

When placing the speakers near a TV set, turn off the TV’s main power switch or unplug it before installing the speakers.
Then wait at least 30 minutes before turning on the TV’s main power switch again.
Some TVs may still be affected even though you have followed the above instructions. If this happens, move the speakers away from the TV.

Connect your TV directly to the System. Connecting the System to a TV via a VCR or an HDD DVD recorder may interfere with your viewing. Connecting an integrated TV/VCR system 
to the System may also interfere with your viewing.

•

•
•
•
•
•

–

–

•

0510YOMMDWCDT

©2010 Victor Company of Japan, Limited

For turning off the demonstration display, see 
“Canceling the display demonstration” in “Initial 
settings.”

Thank you for purchasing a JVC product.

CD-R/-RW: Recorded in the Audio CD, Video CD, and 
SVCD formats. MP3, WMA, JPEG, MPEG-1, MPEG-2, and 
DivX*

1

 files written in accordance with the “ISO 9660” 

format can also be played.

DVD-R/-RW, +R/+RW: Recorded in the DVD Video format. 
MP3, WMA, JPEG, MPEG-1, MPEG-2, and DivX*

1

 files 

written in the UDF-Bridge format can also be played.

DVD-R/-RW: Recorded in the DVD Video Recording (VR) 
format.

USB mass storage class device, SD/SDHC card: MP3, WMA, 
JPEG, MPEG-1, MPEG-2, and DivX*

1

 files.

In addition to the above discs/files, this System can play 
back audio data recorded on CD-Extra.

The following discs cannot be played back: DVD-RAM, 
CD-I (CD-I Ready) and Photo CD. Playing back these discs 
will generate noise and damage the speakers.
It is possible to play back finalized +R/+RW (DVD Video 
format only) discs. The DVD indicator lights up when a 
+R/+RW disc is loaded.
“DVD Logo” is a trademark of DVD Format/Logo Licensing 
Corporation.
The System recognizes up to 999 tracks (files) and 130 
groups.

*

1

 Maximum resolution:

720 × 480@30fps / 720 × 576@25fps

•

•

•

•

For MP3/WMA playback...

Some MP3/WMA files may not be played back due to 
their recording conditions.
This System can play only a disc of ISO 9660 Level 1 or 
Level 2.
It is recommended to record each file at a sampling rate 
of 44.1 kHz and at a data transfer rate of 128 kbps.
This System cannot play back files made at a bit rate of 
less than 64 kbps.
This System can show the Tag data (Version 1).

For playback of files on a USB mass storage class device/
SD card...

You cannot play back files larger than 2 GB.
This System may not play back some USB mass storage 
class devices/SD cards and does not support DRM 
(Digital Rights Management).

This System can play back files on DVD, CD*

2

, USB mass 

storage class device*

2

 and SD/SDHC card*

2

 recorded 

by JVC EVERIO camcorders with the extension <.mod>. 
These files cannot be played back if HD format is used.

*

2

  Only when the maximum bit rate is less than 2 Mbps.

Connect a PAL or NTSC TV to this System.
This System can play back discs recorded in PAL and 
NTSC video format.

Note on Region Code
DVD players and DVDs have their own Region Codes. 
This System can play back only DVDs with an appropriate 
Region Code.

Country/area

Region Code

Middle East and Saudi Arabia

2

Southeast Asia

3

Central and South America

4

Ex.: For Southeast Asia

“RG ERROR” appears if a DVD with an incompatible 
Region Code is loaded.

Caution for DualDisc playback
The Non-DVD side of a “DualDisc” does not comply with 
the “Compact Disc Digital Audio” standard. Therefore, the 
use of the Non-DVD side of a DualDisc in this product may 
not be recommended.

•

–

–

–

–

–

•

–
–

•

•
•

•

If you have already set the clock before, press CLOCK 
repeatedly until the clock setting mode is selected.

To go back to the previous step, press CANCEL while 
holding SHIFT.

The clock may gain or lose 1 to 2 minutes per month. You 
may need to readjust the clock periodically.

•

•

•

The remote control buttons are used for explaining the 
operations unless mentioned otherwise. However, if the 
System has the same or similar button names, they can 
also be used for the operations.
The English on-screen displays and terms are used for 
explanation though you can change the on-screen 
language.
“SD card” refers to both SD card and SDHC card.
“File” and “track” are used interchangeably.

•

•

•
•

Main unit—CA-UXF4VB
Output Power: 

100 W (50 W + 50 W) at 6 Ω (10% THD)

Audio Input: 

AUDIO IN: Stereo mini (ø 3.5 mm)

Microphone Input: 

MIC: Monaural mini (ø 3.5 mm)

Audio output: SUBWOOFER OUT: 

500 mV/10 kΩ

Digital output: OPTICAL DIGITAL OUT:
 

–21 dBm to –15 dBm (660 nm ±30 nm)

VIDEO OUT × 1
COMPONENT VIDEO OUT × 1
Speaker impedance: 

6 Ω – 16 Ω

Tuner
FM frequency: 

87.50 MHz – 108.00 MHz

AM frequency 

For Saudi Arabia: 

531 kHz – 1 602 kHz

 

(at 9 kHz intervals)

 

530 kHz – 1 600 kHz

 

(at 10 kHz intervals)

For other countries/areas: 

531 kHz – 1 710 kHz

 

(at 9 kHz intervals)

 

530 kHz – 1 710 kHz

 

(at 10 kHz intervals)

USB
USB specification: 

Compatible with USB 2.0 Full Speed

Compatible device: 

Mass storage class

Compatible system: 

FAT16, FAT32

Output power: 

DC 5 V 

 500 mA

SD
Compatible device: 

SD, SDHC

Compatible system: 

FAT16, FAT32

Select the video signal output setting according to the 
type of your TV.

You can set the scanning mode only when “DVD/CD,” 
“USB,” or “SD” is selected as the source.

Select “INTERLACE-YUV” when you have connected your 
TV to the System using a composite video cord.

•

•

Optical digital cord 
(not supplied)

When playing multi-channel encoded software, 
the System properly converts the multi-channel 
signals into 2 channels, and emits the downmixed 
sound from the speakers. To enjoy the powerful 
sound of the multi-channel encoded software, 
connect a proper decoder or an amplifier with 
a built-in decoder to the OPTICAL DIGITAL OUT 
terminal.
Set “AUDIO OUT” in the “

” menu correctly 

according to the connected digital audio 
equipment (see “Setup menu operations of the 
System” on page 4).
The digital signal is transmitted through the 
OPTICAL DIGITAL OUT terminal when “DVD/CD,” 
“USB,” or “SD” is selected as the source.

•

•

•

From the powered 
subwoofer
(not supplied)

Before connecting the 
System to the power supply, 
make sure that the powered 
subwoofer is turned off.

P-SCAN YPBPR

For a progressive TV.
Select to enjoy a progressively 
scanned picture through the 
COMPONENT VIDEO OUT jacks.

PRGR. (Progressive) indicator lights 
up.

•

INTERLACE-
YUV

For a conventional TV.
Select when connecting the TV through 
the VIDEO OUT jack.

After connecting a TV, select the appropriate video signal 
output setting according to the connection method. See 
“Setting the scanning mode” in “Initial settings” below.

(On the main unit)

(Hold)

DIGITAL VIDEO

SUPER VIDEO

Component video 
cord (not supplied)

Green

Red

Blue

SUPER VIDEO

General
Power source: 

AC 110 V– 127 V/AC 220 V– 240 V 

 

(adjustable with the voltage selector), 50 Hz/60 Hz

Power consumption (at operation): 

45 W

Power consumption (on standby): 

1.00 W or less

Dimensions (approx.) (W × H × D) (including projecting 
parts): 

236 mm × 123 mm × 285 mm 

Mass (approx.): 

2.0 kg

Speaker—SP-UXF4VB
Speaker type:  Bass-reflex type (Magnetically-shielded type)
Tweeter: 4 

cm

Woofer: 12 

cm

Impedance: 6 

Ω

Dimensions (approx.) (W × H × D) (including projecting 
parts): 

141 mm × 250 mm × 181 mm

Mass (approx.): 

2.2 kg each

Supplied accessories
See “Supplied accessories” in “Getting started.”

Main unit

Speaker

Speaker

Main unit

To get the best performance of the System, keep your discs 
and the mechanism clean.

Remove the disc from its case by holding it at the edge 
while pressing the center hole lightly.
Do not touch the shiny surface of the disc, or bend the 
disc.
Put the disc back in its case after use.
Be careful not to scratch the surface of the disc when 
placing it back in its case.
Avoid exposure to direct sunlight, temperature extremes, 
and moisture.

To clean the disc:
Wipe the disc with a soft cloth in a straight line from center 
to edge.

Stains should be wiped off with a soft cloth. If the System 
is heavily stained, wipe it with a cloth soaked in water-
diluted neutral detergent and wrung well, then wipe 
clean with a dry cloth.
Since the System may deteriorate in quality, become 
damaged or get its paint peeled off, be careful about the 
following:

DO NOT wipe it hard.
DO NOT wipe it with thinner or benzine.
DO NOT apply any volatile substances such as 
insecticides to it.
DO NOT allow any rubber or plastic to remain in contact 
for a long time.

•

•

•
•

•

•

•

–
–
–

–

From 

left 

speaker

From 
right 

speaker

(While holding...)

INTERLACE-YUV

On the TV screen

Red

Black

Composite video cord 
(supplied)

P-SCAN YPBPR

INTERLACE-YUV

NOTE:
Keep the AM loop antenna cable wrapped around the 
AM loop antenna frame, otherwise the effectiveness 
and sensitivity of the AM loop antenna may be 
reduced.

AM loop antenna 
(supplied)

Yellow

To a wall outlet

If a wall outlet does not match the AC plug, use the 
supplied AC plug adaptor (not supplied for Middle 
Eastern and Saudi Arabian models).

•

When you connect a TV using a component video cord, 
you can enjoy a high quality picture by selecting the 
progressive scanning mode. To select the scanning 
mode, see “Setting the scanning mode” in “Initial 
settings” below.

CAUTION for mains (AC) line
BEFORE PLUGGING IN, do check that your mains (AC) 
line voltage corresponds with the position of the 
voltage selector switch provided on the outside of this 
equipment and, if different, reset the voltage selector 
switch, to prevent from a damage or risk of fire/electric 
shock.

Turn it until the best reception 
is obtained.

Red

Black

Black

White

EN_UXF4VB[USUXUGUW].indd   1

EN_UXF4VB[USUXUGUW].indd   1

10.5.10   7:49:02 PM

10.5.10   7:49:02 PM