Toshiba sd-480eke ユーザーズマニュアル
15
Connections
Connections
Notes
• DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the AC-3 RF input of a Dolby Digital Receiver. This
• DO NOT connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the AC-3 RF input of a Dolby Digital Receiver. This
input on your A/V Receiver is reserved for Laserdisc use only and is incompatible with the COAXIAL DIGITAL AUDIO OUT jack
of the DVD player.
of the DVD player.
• Connect the COAXIAL DIGITAL AUDIO OUT jack of the DVD player to the “DIGITAL (COAXIAL)” input of a Receiver or Processor.
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall
• Refer to the owner’s manual of the connected equipment as well.
• When you connect the DVD player to other equipment, be sure to turn off the power and unplug all of the equipment from the wall
outlet before making any connections.
• The output sound of the DVD player has a wide dynamic range. Be sure to adjust the receiver’s volume to a moderate listening
level. Otherwise, the speakers may be damaged by a sudden high volume sound.
• Turn off the amplifier before you connect or disconnect the DVD player’s power cord. If you leave the amplifier power on, the
speakers may be damaged.
• For connection to your TV, see “Connecting to a TV” .
• This section uses the following reference marks.
• This section uses the following reference marks.
: Front speaker
: Rear speaker
: Sub woofer
: Center speaker
: Signal flow
Connecting to Optional Equipment
You can enjoy high quality dynamic sounds by connecting the DVD player to optional audio equipment.
Warning
• When you are connecting (via the COAXIAL DIGITAL
• When you are connecting (via the COAXIAL DIGITAL
AUDIO OUT jack) an AV decoder that does not have Dolby
Digital, Digital Theater Systems (DTS) or MPEG2 decoding
function, be sure to set “Digital Output” to “PCM” from the
on-screen displays. Otherwise, high volume sound may
damage your hearing as well as the speakers.
Digital, Digital Theater Systems (DTS) or MPEG2 decoding
function, be sure to set “Digital Output” to “PCM” from the
on-screen displays. Otherwise, high volume sound may
damage your hearing as well as the speakers.
• When playing DTS-encoded discs (DVDs and audio CDs),
excessive noise may be output from the analog audio output
jacks. To avoid possible damage to the audio system, you
should take proper precautions when the analog audio output
jacks of the DVD player are connected to an amplification
system. To enjoy DTS Digital Surround™ playback, an
external 5.1 channel DTS Digital Surround™ decoder
system must be connected to the COAXIAL DIGITAL
AUDIO OUT jack of the DVD player.
jacks. To avoid possible damage to the audio system, you
should take proper precautions when the analog audio output
jacks of the DVD player are connected to an amplification
system. To enjoy DTS Digital Surround™ playback, an
external 5.1 channel DTS Digital Surround™ decoder
system must be connected to the COAXIAL DIGITAL
AUDIO OUT jack of the DVD player.
Content of the output for each output jack is shown in the following table
and differ depending on the On-Screen Display Setting:
"Video Output" HDMI Output
HDMI
Video
Component
AV
Setting
Setting *
Output
Output
Output
Output
RGB
Invalid
-
Composite
-
RGB
Component Invalid
-
Composite
576i
Composite
(Interlaced)
P-Scan Invalid
-
Composite
576p
Composite
(Progressive)
576p
576p
Composite
576p
Composite
HDMI
720p
720p
-
-
-
1080i
1080i
-
-
-
1080p
1080p
-
-
-
* Settings for HDMI output format are performed using the HDMI button
on the remote control or the HDMI SELECT button on the front panel.
Content of output for each output jack
On-Screen Display Setting
Note
If Auto is selected, it follows preference HDMI aspect ratio of TV.