LG d5966g ユーザーズマニュアル

ページ / 80
I N S TA L L AT I O N   I N S T RU C T I O N S
I N S TA L L AT I O N   I N S T RU C T I O N S
19
Testing Dryer Heating
GAS MODELS
Close the dryer door, press the ON/OFF switch 
to turn the dryer on, and start the dryer on a heat 
setting. When the dryer starts, the igniter should 
ignite the main burner.
NOTE: If all air is not purged from the gas line, 
the gas igniter may turn off before the main 
burner ignites. If this happens, the igniter will 
reattempt gas ignition after approximately 
two minutes.
ELECTRIC MODELS
Close the dryer door, press the ON/OFF switch 
to turn the dryer on, and start the dryer on a heat 
setting. The exhaust air should be warm after the 
dryer has been operating for 3 minutes.
Checking Airflow
Effective dryer operation requires proper airflow. 
The adequacy of the airflow can be measured 
by evaluating the static pressure. Static pressure 
in the exhaust duct can be measured with 
a manometer, placed on the exhaust duct 
approximately 2 ft. (60.9 cm) from the dryer. 
Static pressure in the exhaust duct should not 
exceed 0.6 in. (1.5 cm). The dryer should be 
checked while the dryer is running with no load.
Checking Levelness
Once the dryer is in its final location, recheck 
the dryer to be sure it is level. Make sure it is 
level front to back and side to side, and that 
all 4 leveling feet are firmly on the floor. 
FINAL INSTALLATION CHECK
Once you have completed the installation of 
the dryer and it is in its final location, confirm 
proper operation with the following tests.
Any installation in a manufactured or mobile 
home must comply with the Manufactured Home 
Construction and Safety Standards Title 24 CFR, 
Part 32-80 or Standard CAN/CSA0Z240 MH and 
local codes and ordinances. If you are uncertain 
whether your proposed installation will comply 
with these standards, please contact a service 
and installation professional for assistance.
•  A gas dryer must be permanently attached to 
the fl oor.
•  The electrical connection for an electric dryer 
must be a 4-wire connection. More detailed 
information concerning the electrical connection 
is provided in the section Connecting Electric 
Dryers
.
•  To reduce the risk of combustion and fi re, the 
dryer must be vented to the outside.
•  DO NOT vent the dryer under a manufactured 
home or mobile home.
•  Electric dryers may be vented to the outside 
using the back, left, right, or bottom panel.
•  Gas dryers may be vented to the outside using 
the back, left, or bottom panel. Gas dryers may 
not be vented to the outside using the right side 
panel because of the burner housing.
•  The dryer exhaust duct must be affi xed securely 
to the manufactured or mobile home structure, 
and the exhaust duct must be made of a 
material that will resist fi re and combustion. 
It is recommended that you use a rigid or 
fl exible metal duct.
•  DO NOT connect the dryer exhaust duct 
to any other duct, vent, chimney, or other 
exhaust duct.
•  Make sure the dryer has adequate access to 
outside fresh air to ensure proper operation. 
The opening for outside fresh air must be at 
least 25 in
2
 (163 cm
2
).
•  It is important that the clearance of the duct 
from any combustible construction be at least 
2 in. (5 cm), and when venting the dryer to 
the outdoors, the dryer can be installed with a 
clearance of 1 in. (2.5 cm) at the sides and back 
of the dryer.
•  Please be aware that venting materials are 
not supplied with the dryer. You should obtain 
the venting materials necessary for proper 
installation.
SPECIAL REQUIREMENTS FOR MANUFACTURED OR MOBILE HOMES