Sharp AL-2040CS ユーザーズマニュアル
62
STATUS INDICATORS
When the following indicators light up or blink on the operation panel or the following
alphanumeric codes appear in the display, solve the problem immediately referring
to both the table below and the relevant page.
alphanumeric codes appear in the display, solve the problem immediately referring
to both the table below and the relevant page.
Be sure to use only genuine SHARP parts and supplies.
Indication
Cause and remedy
Page
Drum replacement
required indicator
required indicator
Steadily
lit
lit
Replacement of drum cartridge will be needed
soon. Prepare a new cartridge.
soon. Prepare a new cartridge.
71
Blinking Drum cartridge must be replaced. Replace it with a new one.
58
TD cartridge
replacement
required indicator
replacement
required indicator
Steadily
lit
lit
Replacement of TD cartridge will be needed
soon. Prepare a new cartridge.
soon. Prepare a new cartridge.
71
Blinking TD cartridge must be replaced. Replace it with a new one.
57
Misfeed indicator
Blinking
A misfeed has occurred. Remove the misfed paper
referring to the description of "MISFEED REMOVAL".
referring to the description of "MISFEED REMOVAL".
63
SPF misfeed
indicator
indicator
Steadily
lit
lit
When the document feeder cover is open.
–
Blinking
An original misfeed has occurred in the SPF.
Remove the misfed originals referring to the
description of "E: Misfeed in the SPF".
Remove the misfed originals referring to the
description of "E: Misfeed in the SPF".
67
Power save indicator is
steadily lit.
steadily lit.
The unit is in the preheat mode. Press any key to
cancel the preheat mode.
cancel the preheat mode.
54
The unit is in the auto power shut-off mode.
Press the start (
Press the start (
) key to cancel the auto power
shut-off mode.
54
The paper tray indicator is
blinking.
blinking.
The paper tray is not pushed in correctly, or there
is no paper in the tray. Push the tray all the way
in or load paper in the tray.
is no paper in the tray. Push the tray all the way
in or load paper in the tray.
–
"CH" is blinking in the display.
The TD cartridge is not installed. Check if the
cartridge is installed.
cartridge is installed.
57
"CH" is steadily lit in the
display.
display.
Side cover is open. Close the side cover securely
by pressing the round projections near the side
cover open button.
by pressing the round projections near the side
cover open button.
–
"OP" is blinking in the display.
This appears if it is detected that the OC cover is
open when copying is started. Completely close
the OC cover, or press the start (
open when copying is started. Completely close
the OC cover, or press the start (
) key again.
Depending on the color and the density of the
original, "OP" blinking may appear even when
the OC cover is closed. In such a case, press the
start key again to make a copy.
original, "OP" blinking may appear even when
the OC cover is closed. In such a case, press the
start key again to make a copy.
–
"P" is blinking in the display.
The paper tray or multi-bypass tray is empty.
Load paper.
Load paper.
15, 17
A misfeed has occurred in the paper tray or
multi-bypass tray. Remove the misfed paper.
multi-bypass tray. Remove the misfed paper.
63
A letter and a number appear
alternately.
alternately.
The scan head locking switch is locked. Unlock
the scan head locking switch.
the scan head locking switch.
9
A letter and a number appear
alternately.
alternately.
The unit will not function. Turn the power switch
off, remove the power cord from the outlet, and
contact our Technical Assistance Department at
1-(630)378-3590 in the USA.
off, remove the power cord from the outlet, and
contact our Technical Assistance Department at
1-(630)378-3590 in the USA.
–
08-Trouble.fm 62 ページ ２００７年４月１８日 水曜日 午後１時１２分