Shark gi465d ユーザーズマニュアル

2. Set the temperature dial to the "Max" 

position. Place the iron on its heel 

(on a stable, protected surface) and 

allow it to heat for approximately 2 

minutes.

3. With the iron in a horizontal position, 

press the burst of steam button 

several times to prime the pump. 

(Fig. 4)

4. Turn the temperature dial to any of 

the temperatures within the steam 

band and allow the iron to heat for 

approximately 2 minutes before 

ironing. Place iron on its heel (on a 

stable, protected surface) while the 

iron is warming to desired 

temperature.

5. Slide the variable steam control lever 

up to increase the amount of steam. 

When using extra steam, the iron 

uses more water and it may be 

necessary to fill the tank more often. 

See page 4.

Always read garment labels and follow 

the manufacturer’s ironing instructions. 

Refer to the "Ironing Chart" on page 10 

for temperature recommendations:

•

Use low settings for synthetics.

•• Use moderate settings for wool, 

silks, and blends.

••• Use high settings for cottons and 

linens.

•

Sort articles to be ironed according 

to the type of fabric. This will reduce 

the need to adjust the temperature 

for different types of garments.

•

If you are not sure of the fiber 

content of a garment, test a small 

area such as a seam or inside hem 

section before ironing a visible area. 

Start with a low temperature setting 

and gradually increase to find the 

best setting.

•

When reducing the temperature to 

iron sensitive fabrics, allow 

approximately 2 minutes for the iron 

to cool to the new temperature 

setting.

•

Fabrics such as velour, wool, linen 

and silk are best ironed with an 

ironing cloth to prevent shine marks.

NOTE: Before starting to iron delicate 

fabrics, it is best to first test the 

temperature of the iron on a hem or 

an inside seam.

The auto shut-off safety function of your 

iron is designed to engage from any 

position after approximately 7 minutes of 

non-use. The auto shut-off indicator light 

will turn on when the auto shut-off has 

been activated. (Fig. 8) To reset your iron 

and continue ironing follow these steps.
1) Lift iron from ironing board.

2) Holding the iron horizontally in front of 

you, gently rock the iron back and 

forth several times. This motion will 

reset the safety switch inside the iron. 

The temperature indicator light will 

illuminate when the auto shut-off system 

has been reset. Allow time for the iron to 

re-heat. The temperature indicator light 

will go out when the iron is ready for use.

Vertical steaming enables you to 

remove wrinkles from delicate 

garments without having to rest them 

on the ironing board, i.e. jackets, 

curtains, etc…

1. Place garment on a hanger, away 

from other garments or people.

2. Hold the iron in a vertical position 

and press the steam button. 

(Fig. 6)

6. Steam is produced as soon as the 

iron is held in the horizontal position. 

Steam will stop coming out when the 

iron is put on its heel in a vertical 

position or by sliding the steam lever 

to "0".

NOTE: If the tank runs dry, remove the 

plug from wall outlet. Then, fill the iron 

with water and re-prime the pump. The 

iron may be filled with water while it is 

hot.

The water spray is useful on fabrics with 

stubborn wrinkles. Press the spray 

button and a jet of water will spray onto 

the fabric being ironed. (Fig. 5) The 

water spray can be used with dry or 

steam ironing as desired.

The burst-of-steam button is useful 

when ironing denim, cotton, and linens. 

It provides extra, sudden blasts of 

steam which aid in removing stubborn 

wrinkles.

The burst-of-steam feature can be used 

with Dry or Steam ironing as desired.

1. Make sure the water tank is at least 

1/2 filled with water.