Sharp aquos lc-46d78un ユーザーズマニュアル

Troubleshooting

Problem

Possible Solution

• No power

• Check if you pressed POWER on the remote control unit.

Page 12

If the indicator on the TV does not light up, press POWER on the TV.
• Is the AC cord disconnected?

Page 8

• Has the power been turned on?

Page 12

• Unit cannot be operated.

• External infl uences such as lightning, static electricity, may cause improper

operation. In this case, operate the unit after fi rst turning off the power of the TV or
unplugging the AC cord and replugging it in after 1 or 2 minutes.

• Remote control unit does not

operate.

• Are batteries inserted with polarity (

e, f) aligned?

Page 9

•  Are batteries worn out? (Replace with new batteries.)
•  Are you using it under strong or fl uorescent lighting?
•  Is a fl uorescent light illuminated near the remote control sensor?
•  Is "RC Control Lock" selected in "Operation Lock Out"?

Page 25

• Picture is cut off/with sidebar

screen.

• Is the image position correct?

Page 21

• Are screen mode adjustments such as picture size made correctly?

Page 16

• Strange color, light color, or

color misalignment

• Adjust the picture tone.

Pages 18 and 19

• Is the room too bright? The picture may look dark in a room that is too bright.

• Power is suddenly turned off.

• Is the sleep timer set?

Page 13

• Check the power control settings.

Pages 19 and 20

• The unit's internal temperature has increased. Remove any objects blocking vent or

clean.

• No sound

• Is connection to other components correct?

Page 11

• Is the volume too low?

Page 13

• Is “Variable” selected in “Output Select”?

Page 24

• Have you pressed MUTE on the remote control unit?

Page 13

• Check the audio output of the connected external equipment. Is the volume too low

or muted?

• When external equipment is connected via an HDMI cable, you may need to

confi gure the audio to be output through the HDMI cable.

• When audio is not output from external equipment connected to the INPUT 4 or

INPUT 6 terminal, check the "PC Audio Select" setting.

Page 24

• Even when external equipment is connected using an HDMI-certifi ed cable, an audio

cable connection may be required depending on the type of equipment and the
media being played back. In this case, in addition to connecting an HDMI-certifi ed
cable to the INPUT 6 (HDMI) terminal, connect a ø 3.5 mm stereo minijack cable to
the AUDIO terminal and set "PC Audio Select" to "Input 6 (HDMI)".

Page 24

• When connecting a PC via an HDMI-certifi ed cable, check the following:

- Is the audio output of the PC confi gured correctly? Check the audio output

settings and output audio format in Sound Properties on the PC.

Only PCM format audio can be output. Compressed audio (with a sampling rate of
32kHz, 44.1kHz, or 48kHz) and DTS format audio cannot be output.

- Depending on the board, only video signals may be output. In this case, in addition

to connecting an HDMI-certifi ed cable to the INPUT 6 (HDMI) terminal, connect a
ø 3.5 mm stereo minijack cable to the AUDIO terminal and set "PC Audio Select"
to "Input 6 (HDMI)".

Page 24

• If you are using a DVI-HDMI conversion cable to connect external equipment to the

TV, check the following:
- Is an audio cable connected? The DVI-HDMI conversion cable is for video only.

Connect a ø 3.5 mm stereo minijack cable to listen to the audio.

- Is INPUT 6 being used? When the TV is connected to another HDMI terminal, the

audio and video are not output together even if a ø 3.5 mm stereo minijack cable
is connected to the shared AUDIO terminal for INPUT 4 and INPUT 6.

- Is "Input 4 (PC)" selected in "PC Audio Select"?

Page 24

Appendix

LC-46D78UN_E.indb 27

2010/02/25 17:47:15