Philips PQ202 ユーザーズマニュアル

 5 

 Clean the shaver after every 

shave, see chapter ‘Cleaning and 

maintenance’. 

 6 

 Put the protection cap on the shaver 

after use to prevent damage and to 

avoid dirt accumulation in the shaving 

heads (Fig. 8).
Cleaning and maintenance

Never use scouring pads, abrasive cleaning 

agents or aggressive liquids such as petrol 

or acetone to clean the appliance. 
Clean the shaver after every shave to 

guarantee better shaving performance.

For the best cleaning result, we advise you 

to use Philips Cleaning Spray (HQ110).  

Ask your Philips dealer for information.

 1 

 Switch off the shaver.

 2 

 Clean the top of the appliance with 

the cleaning brush supplied (Fig. 9).

 3 

 Press the release button (1) and pull 

the shaving unit a straight up off the 

shaver (2) (Fig. 10).

 4 

 Clean the inside of the shaving unit 

with the cleaning brush (Fig. 11).

 5 

 Clean the hair chamber with the 

cleaning brush (Fig. 12).

 6 

 Put the shaving unit back onto the 

shaver (Fig. 13).
Every two months: shaving heads

 1 

 Switch off the shaver.

 2 

 Press the release button (1) and pull 

the shaving unit straight up off the 

shaver (2) (Fig. 10).

 3 

 To remove the retaining frame, 

push the sides of the central spring 

towards each other (1). Then lift the 

retaining frame out of the shaving unit 

(2) (Fig. 14).

 4 

 Slide the shaving heads out of  

the retaining frame. Remove and  

clean one shaving head at a time.  

Each shaving head consists of a cutter 

and a guard (Fig. 15).

 5 

 Remove the guard from the 

cutter (Fig. 16).

 6 

 Clean it with the short-bristled side of 

the cleaning brush. Brush carefully in 

the direction of the arrows (Fig. 17).

 7 

 Clean the guard with the long-bristled 

side of the cleaning brush (Fig. 18)

 8 

 Put the cutter back into the guard 

after cleaning (Fig. 19).

 9 

 Slide the shaving heads back into the 

retaining frame.  (Fig. 20)

 10 

 Put the retaining frame back into the 

shaving unit (‘click’) (Fig. 21).

 11 

 Put the shaving unit back onto the 

shaver (Fig. 13).
storage 

Keep the appliance dry.

Use and store the appliance at a 

temperature between 5°C and 35°C.

 1 

 Switch off the shaver.

 2 

 Put the protection cap on the shaver 

after use to prevent damage and to 

avoid dirt accumulation in the shaving 

heads (Fig. 22).
Replacement

Replace the shaving heads every two years 

for optimal shaving results.

Replace damaged or worn shaving heads 

with Philips shaving heads only (HQ4+ for 

China or HQ56 for the rest of the world). 

For instructions on how to remove the 

shaving heads, see chapter ‘Cleaning and 

maintenance’, section ‘Every two months: 

shaving heads’.

To retain the top performance of your 

shaver, make sure you clean it regularly 

and replace its shaving heads at the 

recommended time.

 - We advise you to replace your shaving 

heads every two years. Always replace 

them with Philips shaving heads only 

(HQ4+ for China or HQ56 for the 

rest of the world) (Fig. 23).
Cleaning

 - Use Philips Cleaning Spray (HQ110) to 

clean the shaving heads thoroughly.
Environment

 - Do not throw away the appliance 

with the normal household waste at 

the end of its life, but hand it in at an 

official collection point for recycling. 

By doing this, you help to preserve the 

environment (Fig. 24).

 - Batteries contain substances that 

may pollute the environment. Do 

not throw away batteries with the 

normal household waste, but dispose 

of them at an official collection point 

for batteries. Always remove the 

batteries before you discard and hand 

in the appliance at an official collection 

point (Fig. 25).
guarantee and service

If you need service or information or if 

you have a problem, please visit the Philips 

website at www.philips.com or contact 

the Philips Consumer Care Centre in your 

country. You find its phone number in the 

worldwide guarantee leaflet. If there is no 

Consumer Care Centre in your country, go 

to your local Philips dealer.

The shaving heads (cutters and guards) 

are not covered by the terms of the 

international guarantee because they are 

subject to wear.

This chapter summarises the most common 

problems you could encounter with the 

appliance. If you are unable to solve the 

problem with the information below, contact 

the Consumer Care Centre in your country. 

Problem Possible 

cause

Solution

The 

shaver 

does not 

shave as 

well as it 

used to.

The shaving 

heads are 

dirty. You 

have not 

cleaned the 

shaver well 

enough or 

you have 

not cleaned 

it for a long 

time.

Clean the 

shaver thor-

oughly before 

you continue 

shaving. See 

chapter 

‘Cleaning and 

maintenance’.

Long hairs 

obstruct 

the shaving 

heads.

Clean the 

cutters and 

guards with 

the clean-

ing brush 

supplied. 

See chapter 

‘Cleaning and 

maintenance’, 

section ‘Every 

two months: 

shaving heads’.

The shaving 

heads are 

damaged or 

worn.

Replace the 

shaving heads. 

See chapter 

‘Replacement’.

The 

shaver 

does not 

work 

when I 

push the 

on/off 

slide up-

wards.

The bat-

teries are 

placed 

incorrectly.

Make sure 

the + and - 

indications on 

the batteries 

match the 

indications in 

the battery 

compartment.

The bat-

teries are 

empty.

Replace the 

batteries. 

See chapter 

‘Preparing for 

use’.

My 

skin is 

irritated 

after 

shaving.

Your skin 

needs time 

to get used 

to the Philips 

shaving 

system.

Skin irritation 

during the 

first 2-3 

weeks of use 

is possible. 

After this 

period, the 

skin irritation 

usually disap-

pears.

Problem Possible 

cause

Solution

The 

rotation 

speed 

of the 

shaving 

heads is 

slower 

than 

usual.

Too much 

dirt has 

collected in 

the shaving 

heads.

Clean the 

shaving heads. 

See chapter 

‘Cleaning and 

maintenance’.

The bat-

teries are 

empty

Replace the 

batteries. 

See chapter 

‘Preparing for 

use’.

The ap-

pliance 

makes a 

strange 

noise.

Too much 

dirt has 

collected in 

the shaving 

heads.

Clean the 

shaving heads. 

After cleaning, 

lubricate 

the central 

point on the 

inside of the 

guards with 

Philips Clean-

ing Spray 

(HQ110). 

See chapter 

‘Cleaning and 

maintenance’.

The shaving 

heads are 

damaged or 

worn.

Replace the 

shaving heads. 

See chapter 

‘Replacement’.