Manualsbrain.com
  1. マニュアル
  2. ブランド
  3. Philips
  4. VR1010
  5. ユーザーズマニュアル

Philips VR1010 ユーザーズマニュアル

ダウンロード
ページ / 31
— 12 —
         VHF         L         
         VHF         H
         UHF
 
   
SELECT:             CONFIRM: OK
END: MENU
Manual Channel Setting
When you want to do channel setting
manually, follow this procedure.
           
         STORE CHANNEL
         CONTINUE SEARCH 
   
SELECT:
 CONFIRM: OK
END: MENU
Selecting Colour Mode
Before using the VCR, you need to set
the colour mode both for recording and
playback.
Press 
COLOUR MODE
 on the front
panel for more than 2 seconds. The
current setting will appear on the
screen for about 5 seconds. While the
current setting appears, press 
COL-
OUR MODE
 repeatedly, the setting
changes as follows.
For recording:
AUTO: Normally select this mode.
The colour system is
automatically detected.
NTSC3.58: Select this mode if
“AUTO” does not work well
when recording the NTSC
signals. (For playback on an
NTSC TV)
NTSC4.43: Select this mode if
“AUTO” does not work well
when recording the NTSC
signals on the PAL TV. (For
playback on a PAL TV)
PAL:
Select this mode if “AUTO”
does not work well when
recording the PAL signals.
MESECAM: Select this mode if
“AUTO” does not work well
when recording the SECAM
signals.
For playback:
AUTO: Normally select this mode.
When you watch a PAL,
NTSC or MESECAM tape,
the colour system is
automatically detected.
NTSC3.58: Select this mode when
you watch an NTSC3.58
tape on an NTSC TV.
NTSC4.43: Select this mode when
you watch an NTSC4.43
tape on a PAL TV.
NTSC
=
=
=
=
=PAL TV: Select this mode
when you watch an
NTSC3.58 tape on a PAL
TV.
PAL:
Select this mode if “AUTO”
does not work well when
playing back a PAL tape.
MESECAM: Select this mode if
“AUTO” does not work well
when playing back a
MESECAM tape.
When playing back an NTSC tape with
“AUTO” mode selected
The tape is played back using “NTSC3.58”
mode.
1
Select Tuner Set Up Mode
1 Press 
VCR
.
2 Press 
MENU
.
3 Press 
PLAY
 
5 or 
STOP
 
∞ to select
“TUNER SET UP” then press 
OK/
STATUS
.
4 Press 
PLAY
 
5 or 
STOP
 
∞ to select
“CHANGING TUNER SET UP”
then press  
OK/STATUS
.
The programmed channel informa-
tion list appears with the settings of
the tuned channel flashing. (You can
also watch the picture of the tuned
channel since the list and the picture
alternates on the TV.)
2
Select Station
1 Press 
PLAY
 
5 or
STOP
 
∞ until an
open channel in
which you want to
store a new chan-
nel starts flashing then press 
OK/
STATUS
.
2 Press 
PLAY
 
5 or 
STOP
 
∞ to select
the search starting band.
VHF L: Starts searching from the
VHF L band.
VHF H: Starts searching from the
VHF H band.
UHF:
Starts searching from the
UHF band.
3 Press 
OK/STATUS
. Searching
starts, and when a station is tuned in,
searching stops and the tuned
frequency is shown on the TV.
Then the following menu appears.
3
Store Channel
Press 
PLAY
 
5 or 
STOP
 
∞ to select
“STORE CHANNEL” then press
OK/STATUS
.
The programmed channel information
list appears again with the settings of
the newly tuned channel flashing.
• If you do not want to store this station,
select “CONTINUE SEARCH” then
press 
OK/STATUS
, searching starts
again.
4
Finish Setting
Press 
MENU
.
S
ETTING
 
U
P
  
(C
ONTINUED
)
vr1010/75
00.6.29, 4:53 PM
12