Philips VR1100 ユーザーズマニュアル
— 12 —
Do NOT press any button on the front panel or remote control until the display window shows either the display as
illustrated in step 2 or “– –:– –”.
illustrated in step 2 or “– –:– –”.
As AUTO CH. SET
progresses, the “
progresses, the “
7” mark
moves from left to right.
1
¶ If you are referring to the display window, press
5/∞ to select “Auto” and press OK/STATUS.
S
ETTING
U
P
(C
ONTINUED
)
Auto Set Up
¶ If you are referring to the on-screen display, press 5/∞ to
select “AUTO CH. SET” and press OK/STATUS.
AUTO CH. SET
PLEASE WAIT
END : MENU
0
+
+
+
Beginning
End
\ AUTO CH. SET
FOLLOW TV
SELECT:
5∞
CONFIRM: OK
END : MENU
2
¶ If you have connected the VCR to TV via an RF
cable only (RF connection), the channel that is
shown on the display window is your Video Channel.
If you have selected MAGYARORSZAG (36),
CESKA REPUBLIKA (42), POLSKA (48) or
OTHER EASTERN EUROPE (EE) in Preparation
section, “2OUT” appears instead of “1OUT”.
shown on the display window is your Video Channel.
If you have selected MAGYARORSZAG (36),
CESKA REPUBLIKA (42), POLSKA (48) or
OTHER EASTERN EUROPE (EE) in Preparation
section, “2OUT” appears instead of “1OUT”.
To view picture signals from the VCR, set TV to the
Video Channel. Refer to the instructions supplied
with TV set for how to do this.
Video Channel. Refer to the instructions supplied
with TV set for how to do this.
¶ If you have connected the VCR to TV via both an RF
cable and a SCART cable or an S-Video cable (SCART
connection or S-Video connection), you do not need the
video channel so you have to set the video channel to
off.
Press
connection or S-Video connection), you do not need the
video channel so you have to set the video channel to
off.
Press
∞ until the video channel changes to “– –” (off).
To view picture signals from the VCR, set the TV to its
AV mode. Refer to the instructions supplied with the
TV set for how to do this.
AV mode. Refer to the instructions supplied with the
TV set for how to do this.
¶ If “– –:– –” appears, both Auto Channel Set and Auto Clock Set have failed.
Make sure the TV antenna cable is connected correctly and press OK/STATUS to re-perform the Auto Set Up.
3
Press OK/STATUS.
If the correct current time is displayed on the display window, the Auto Channel Set and Clock Set
have been completed successfully. Go to step 4.
have been completed successfully. Go to step 4.
If “1” (channel position) is displayed on the display window, the Auto Clock Set has not completed
(only the Auto Channel Set has). Go to step 4 and then perform “Clock Set” manually. (✈P.20)
(only the Auto Channel Set has). Go to step 4 and then perform “Clock Set” manually. (✈P.20)
¶ You can check if the Guide Channel numbers have been set correctly when you perform S
HOW
V
IEW
Timer
Recording (✈P.29); if the correct channel position number is displayed on S
HOW
V
IEW
Programme screen, this
confirms that the Guide Channel number for the S
HOW
V
IEW
number you enter has been set correctly.
4
Press PROGRAMME
5/∞ on the front panel (or CH 5/∞ on the remote control) to make sure that all necessary
stations have been stored in the VCR’s memory.
¶ If station names (ID ✈P.19) have also been stored in the VCR’s memory, the station name will be displayed at the
top left corner of the screen for about 5 seconds when the VCR is tuned to a different station.
¶ If you want to set the tuner manually such as to add or skip channels, to change channel positions, or to set or station
names, see pages 17–18.
¶ If no station is stored in the VCR’s memory, make sure the TV antenna cable is connected correctly and turn off the
VCR power once, then turn it back on again. Re-perform from Preparation on page 10.
Untitled-2
16/08/2000, 15:36
12