Philips VR1100 ユーザーズマニュアル
— 17 —
2
Select Channel Position
1 Press
5∞ 2 3 until a vacant
position in which you want to store a
channel begins blinking.
channel begins blinking.
2 Press
OK/STATUS
. The Manual
Channel Set screen appears.
3
Set New Channel Information
1 Press
5 or ∞ to change the band
between CH (regular) and CC
(cable), then press
(cable), then press
3.
2 Press the Number buttons to input
the channel you want to store.
• Input “0” before any single number
• Input “0” before any single number
entries.
• To input the registered station name
(ID – ✈P.19), press
3 until “----”
(ID setting) begins blinking, then
press
press
5 or ∞.
• For fine tuning adjustment, press
3
until “+/–” begins blinking, then
press
press
5 or ∞. While tuning, “+” or
“–” appears.
• When storing a channel that sends
scrambled broadcasts, press
3 until
“OFF” (Decoder setting) blinks,
then press
then press
5 or ∞ to set
“DECODER” to “ON” (“OFF” is
the default setting).
When “A/V2 SELECT” is set to
“A/V” or “SAT”, the “DECODER”
setting cannot be changed (✈P.27).
the default setting).
When “A/V2 SELECT” is set to
“A/V” or “SAT”, the “DECODER”
setting cannot be changed (✈P.27).
Auto Channel Setting
If you move to another place, you may
need to tune the VCR tuner again for
your new residential area.
need to tune the VCR tuner again for
your new residential area.
1
Perform Auto Channel Set
1 Press
VCR.
2 Press
MENU
.
3 Press
5 or ∞ to select “AUTO
TUNER SET UP”, then press
OK/STATUS
.
4 Press
5 or ∞ to select your country’s
name, then press
OK/STATUS
.
5 Press
5 or ∞ to select your preferred
language, then press
OK/STATUS
.
6 Press
5 or ∞ to select “AUTO CH.
SET”, then press
OK/STATUS
. The
Auto Set screen appears as below;
The Auto Set screen appears, and
remains on screen while the recorder
searches for receivable stations.
As Auto Channel Set progresses,
the “ ” mark on the screen moves
from left to right.
Wait until the screen as shown in step 2
appears.
remains on screen while the recorder
searches for receivable stations.
As Auto Channel Set progresses,
the “ ” mark on the screen moves
from left to right.
Wait until the screen as shown in step 2
appears.
2
Confirm Programmed Channel
Information List
Information List
Once it is completed, “AUTO CH. SET
COMPLETED” is displayed on the
screen for about 5 seconds.
The following screen will appear after
5 seconds, or if you press
COMPLETED” is displayed on the
screen for about 5 seconds.
The following screen will appear after
5 seconds, or if you press
MENU
;
PR: channel positions
CH: channel numbers
ID: station names (✈P.19)
CH: channel numbers
ID: station names (✈P.19)
• The blueback screen and the
programme currently being broad-
cast by the blinking station
apppear alternately for 8 seconds each.
cast by the blinking station
apppear alternately for 8 seconds each.
• To view the next page, use the
5∞
2 3 buttons on the remote control.
The stations located in the selected
country appear at the top of the list.
The stations located in the selected
country appear at the top of the list.
• The Guide Program numbers will
also be set automatically during Auto
Channel Set.
Channel Set.
3
Finish Setting
Press MENU to exit the menu
operations.
operations.
Notes:
• If you perform Auto Channel Set when the
• If you perform Auto Channel Set when the
aerial cable is not connected properly,
“NO TV SIGNALS” appears on the screen
in step 2. When this happens, make sure of
the aerial connection and press OK/
STATUS; Auto Channel Set will take place
again.
“NO TV SIGNALS” appears on the screen
in step 2. When this happens, make sure of
the aerial connection and press OK/
STATUS; Auto Channel Set will take place
again.
• Depending on reception conditions, the
stations may not be stored in order, and
the station names may not be stored
correctly.
the station names may not be stored
correctly.
Manual Channel Setting
When you want to do channel setting
manually, perform the following
procedures as required.
• If you want to ..........
manually, perform the following
procedures as required.
• If you want to ..........
.......... add channels (See below)
.......... delete unwanted channels
.......... delete unwanted channels
(See page 18)
.......... change the channel
positions (See page 18)
.......... perform fine-tuning (See
page 18)
.......... descramble programmes
when receiving scrambled
broadcasts (See page 18)
broadcasts (See page 18)
.......... change station names (See
page 18)
• If you live in Eastern Europe, see
INFORMATION on page 18 also.
If you want to add channels
1
Access Programmed Channel
Information List
Information List
1 Press
VCR.
2 Press
MENU
.
3 Press
5 or ∞ to select “ MANUAL
TUNER SET UP”, then press
OK/
OK/
STATUS
.
The blueback screen and the
programme currently being broadcast
by the selected channel appear
alternately for 8 seconds each.
programme currently being broadcast
by the selected channel appear
alternately for 8 seconds each.
AUTO CH. SET
PLEASE WAIT
0 – – – – – + – – – –
■
– – – – + – – – – – +
END : MENU
Beginning
End
C: Cable
PR
CH
ID
PR
CH
ID
01
25
ARD
08
C26 E-SP
02 C08
SKY1
09
C33 3SAT
03
10
ZDF
10
55
WEST
04 C65
RAI1
11
C24 SAT1
05 C31
BBC1
12
C23 OSF
06 C32
BBC2
13
C25 ESPN
07 C24
BBC4
14
C48 20G
SELECT :
5∞
EDIT : OK
ERASE : CLEAR
END : MENU
ERASE : CLEAR
END : MENU
∞
∞
PR CH
ID
FINE DECODER
01 CC25 ARTE +/–
OFF
SELECT :
5∞
CURSOR POSITION :
CONFIRM : OK
END : MENU
CONFIRM : OK
END : MENU
∞
∞
The blueback screen and the
programme currently being broadcast
by the selected channel appear
alternately for 8 seconds each.
programme currently being broadcast
by the selected channel appear
alternately for 8 seconds each.
(Ex.) To store in position 12.
PR
CH
ID
PR
CH
ID
01
25 ARD
08
C26 E-SP
02 CDB SKY1
09
55 WEST
03
10
ZDF
10
C24 SAT1
04 C65 RAI1
11
C23 OSF
05 C31 BBC1
12
– – – –
06 C32 BBC2
13
– – – –
07 C33 3SAT
14
– – – –
SELECT:
5∞
EDIT : OK
ERASE : CLEAR
END : MENU
∞
∞
Untitled-2
16/08/2000, 15:37
17