Philips VR1100 ユーザーズマニュアル
— 33 —
ANT. IN
AV1 (L-1)
OUT
AV2 (L-1)
LP30713-006
L
AUDIO
OUT
R
RF OUT
ANTENNE
LP20914-005
SORTIE
PAUSE
TELEC.
TELEC.
S
AUDIO
IN/OUT
ENTRE/SORTIE
IN/DECODER
ENTRE/SORTIE
ENTRE/SORTIE
SORTIE
ANTENNE
ENTREE
ANT. IN
AV1 (L-1)
OUT
AV2 (L-1)
LP30713-006
L
AUDIO
OUT
R
RF OUT
ANTENNE
LP20914-005
SORTIE
PAUSE
TELEC.
TELEC.
S
AUDIO
IN/OUT
ENTRE/SORTIE
IN/DECODER
ENTRE/SORTIE
ENTRE/SORTIE
SORTIE
ANTENNE
ENTREE
Tape Duplication
1 Connect the recording VCR (this VCR) and the playing
VCR.
2 Connect the recording VCR (this VCR) to the TV.
Connection
Diagram
Dubbing from any VCR (or video
camera) to another is simple.
Explanations on this page uses this
VCR as the recording VCR.
Refer also to the manual supplied with
the other VCR (for playback).
camera) to another is simple.
Explanations on this page uses this
VCR as the recording VCR.
Refer also to the manual supplied with
the other VCR (for playback).
Note:
When this VCR is using the
recording VCR,
You can also use S-Video or Video/
Audio input jacks on the front panel if
another VCR has S-Video or Video/
Audio output jacks.
When this VCR is using the playing
VCR,
You can use the following connector or
jacks.
• AV1 (L-1) IN/OUT connector (rear
When this VCR is using the
recording VCR,
You can also use S-Video or Video/
Audio input jacks on the front panel if
another VCR has S-Video or Video/
Audio output jacks.
When this VCR is using the playing
VCR,
You can use the following connector or
jacks.
• AV1 (L-1) IN/OUT connector (rear
panel): if another VCR has scart
input connector.
Be sure to set the A/V1 OUTPUT to
the appropriate mode on the
“OUTPUT/INPUT SET UP” screen.
(✈P.27)
input connector.
Be sure to set the A/V1 OUTPUT to
the appropriate mode on the
“OUTPUT/INPUT SET UP” screen.
(✈P.27)
• S-Video/Audio output jacks (rear
panel): if another VCR has S-Video/
Audio input jacks.
Audio input jacks.
1
At VCRs
Insert a source tape in the playing VCR
and a blank tape in the recording VCR.
and a blank tape in the recording VCR.
2
At TV
Tune the channel on the TV to your
video channel or external line input.
video channel or external line input.
3
Select Line Input
Press Number button “0” and/or
PROGRAMME
5/∞ (or CH 5/∞ on
the remote control) to select the line
input.
• L-1: For rear panel AV1 (L-1) IN/
input.
• L-1: For rear panel AV1 (L-1) IN/
OUT connector.
• L-2: For rear panel AV2 (L-2) IN/
DECODER connector.
• S-1: For front panel S-Video/Audio
input jacks.
• L-F: For front panel Video/Audio
input jacks.
If you are using a rear panel AV1 (L-1)
IN/OUT or AV2 (L-2) IN/DECODER
connector, be sure to set the “A/V1
INPUT” or “A/V2 SELECT” and
“A/V2 INPUT” on the OUTPUT/
INPUT SET UP screen to appropriate
mode. (✈P.27)
IN/OUT or AV2 (L-2) IN/DECODER
connector, be sure to set the “A/V1
INPUT” or “A/V2 SELECT” and
“A/V2 INPUT” on the OUTPUT/
INPUT SET UP screen to appropriate
mode. (✈P.27)
A
DVANCED
O
PERATIONS
(C
ONTINUED
)
4
Select Tape Speed
Press
ALT/SPEED
, until the desired
tape speed (SP or LP) appears on the
display.
display.
5
Play Back Tape
Press the
PLAY
3 button on the
Playing VCR.
6
Record (Copy) Tape
Press
REC/OTR
¶ at this VCR.
Remember: Press the buttons in step 5
and 6 simultaneously to avoid missing
any of the recording.
and 6 simultaneously to avoid missing
any of the recording.
Your VCR
Recorder
21-pin SCART
Cable
Cable
Another VCR
TV Recorder
Another VCR
RF Cable
TV Receiver
VIDEO
CHANNEL
or AV
mode
CHANNEL
or AV
mode
Recorder
Your VCR
Player
Player
S-Video Cable
21-pin SCART
Cable
Cable
Untitled-2
16/08/2000, 15:38
33