Philips vrx260at99 ユーザーズマニュアル
1
Press the POWER button. The VCR light and the PWR.
(power) light will appear on the display panel.
(power) light will appear on the display panel.
2
Turn on the TV. Set it to the same channel as the
CH3/CH4 switch on the back of the VCR. The display shown
below will appear. (If the display does not appear, check your
hookups, then follow the steps on page 12 to set up channels and
page 17 to select a language.)
CH3/CH4 switch on the back of the VCR. The display shown
below will appear. (If the display does not appear, check your
hookups, then follow the steps on page 12 to set up channels and
page 17 to select a language.)
3
Within 60 seconds, press the PLAY/o button or the
STOP/p button to select English or Spanish on-screen
displays.
STOP/p button to select English or Spanish on-screen
displays.
4
Press the MENU button. The display shown below will appear.
SELECT op
→
ENGLISH ON
ESPAÑOL
ESPAÑOL
MAKE SELECTION OR
PUSH MENU TO CONTINUE
PUSH MENU TO CONTINUE
Turning on Your VCR 11
5
Within 60 seconds, press the CHANNEL o button to
begin automatic channel programming. AUTO SET PRO-
CEEDING PLEASE WAIT will appear on-screen. The VCR will
memorize all available channels. When all channels are pro-
grammed, CHANNELS ARE SET will appear on-screen briefly,
then TV programming will appear.
Now, when you press the CHANNEL o/p buttons, you’ll only
scan through channels that you receive.
begin automatic channel programming. AUTO SET PRO-
CEEDING PLEASE WAIT will appear on-screen. The VCR will
memorize all available channels. When all channels are pro-
grammed, CHANNELS ARE SET will appear on-screen briefly,
then TV programming will appear.
Now, when you press the CHANNEL o/p buttons, you’ll only
scan through channels that you receive.
• To skip this feature and play a tape
immediately, insert a tape with its
record tab removed. Or, to skip step
3, press the MENU button. All on-
screen displays will be in English. To
skip step 5, press the STOP/p but-
ton. Channels will not be pro-
grammed, and CHANNELS NOT
SET will appear on-screen.
record tab removed. Or, to skip step
3, press the MENU button. All on-
screen displays will be in English. To
skip step 5, press the STOP/p but-
ton. Channels will not be pro-
grammed, and CHANNELS NOT
SET will appear on-screen.
• If you try to program channels
when there is no antenna or cable
connected to the VCR, programming
will appear to take place, but even-
tually a NO TV SIGNALS message
will appear. Connect an antenna or
cable to the VCR’s ANT(enna) IN
Jack and try again. You may need
to follow the steps on page 12.
connected to the VCR, programming
will appear to take place, but even-
tually a NO TV SIGNALS message
will appear. Connect an antenna or
cable to the VCR’s ANT(enna) IN
Jack and try again. You may need
to follow the steps on page 12.
Helpful Hints
Before turning on your VCR, make sure there are batteries in the
remote control and the VCR and TV are connected correctly.
remote control and the VCR and TV are connected correctly.
●
Follow the steps on this page only when you plug the VCR
power cord into the wall outlet for the first time.
power cord into the wall outlet for the first time.
●
You can not program channels if you are using a Cable Box or
a Direct Broadcast System.
a Direct Broadcast System.
2
Turn on the TV.
CONNECT ANTENNA OR CABLE
TO VCR
TO VCR
THEN . . .
PUSH CH UP KEY
OR . . .
FOR PLAY ONLY – PUSH STOP
POWER
EJECT
VCR/TV
1
2
3
4
5
6
7
8
9
0
CHANNEL
MEMORY
STATUS/EXIT
CLEAR
SLOW
MENU
REWIND
/PLAY
F.FWD
REC/OTR
PAUSE/STILL
/STOP
+100
TIME SEARCH
SPEED
VCR PLUS+
1
3
4
5
VRX260 LAYOUT 4/8/99 8:52 PM Page 11