Crestron clt-1dim4 clx-1dim4 ユーザーズマニュアル

 

CLT- & CLX-1DIM4 

The Crestron



 1-Feed, 4-Dimmer Terminal Block and 

Module (CLT-1DIM4 and CLX-1DIM4, respectively), 
are considered a single entity and must be used together. 
They ship separately to permit termination of the field 
wiring to the CLT-1DIM4 prior to installation of the 
CLX-1DIM4, as described in this guide. They can be 
mounted in any Crestron Automation Enclosure (CAEN-
Series Enclosures). The terminal block is designed to 
terminate the circuit feed (LINE and NEUTRAL) and 
distribute the controlled circuit (LOAD) to the fixtures. 
The module connects to the terminal block and performs 
dimming control of four incandescent, magnetic low 
voltage, neon, cold cathode, or dimmable 2-wire 
fluorescent lighting loads. The maximum load is 16 amps 
for any controlled circuit, limited to 16 amps total per 
module. The unit requires 120VAC 60 Hz, 1 phase input 
voltage. An oversize heat sink dissipates heat efficiently. 
There are LEDs on the module to indicate communication 
to a Cresnet



 network, input power to the module, and 

output power to the load. 

NOTE:  When connecting to an Arc Fault Breaker, the 
load should not exceed 1000 watts total.  

This product is Listed to applicable UL Standards and 
requirements by Underwriters Laboratories Inc. 

     

(E103692)

 

Terminal block and module must be mounted into a 
Crestron Automation Enclosure by a licensed electrician, 
in accordance with all national and local codes.  

CAUTION:  This equipment is for indoor use only and 
needs to be air-cooled. Mount in a well-ventilated area. 
The ambient temperature must be 32

°F to 104°F (0°C to 

40

°C). The relative humidity must be 0% to 90% (non-

condensing).  

Terminal blocks are installed along the left side of single-
wide enclosures and along the outside edges (left and 
right sides) of double-wide enclosures. Modules are 
installed along the right side of single-wide enclosures 
and side-by-side in the center of double-wide enclosures. 
When installing modules and terminal blocks in a double-
wide enclosure, be sure to invert units on the right side so 
that they can be properly wired. Refer to the illustrations 

shown below when considering the location of terminal 
blocks and modules within an enclosure.  

NOTE:  Modules and terminal blocks must be installed 
into the lowest available spaces and continue toward the 
top of the enclosure. 

N OUT 4

N OUT 3

N OUT 2

N OUT 1

120VAC 60 Hz

16A MAX

GROUNDING

TERMINAL

BLOCK

DIM 4

DIM 3

DIM 1

DIM 2

LINE

TERMINAL

BLOCK

N IN

MODULE

 

 

TERMINAL BLOCK

(RIGHT)

N OUT 4

GROUNDING TERMINAL BLOCKS

TERMINAL BLOCK

(LEFT)

N OUT 3

N OUT 2

N IN

N OUT 1

DIM 4

DIM 3

DIM 1

DIM 2

LINE

120VAC 60 Hz

16A MAX

MODULE

N OUT 4

N OUT 3
N OUT 2

N OUT 1

N IN

DIM 4

DIM 3

DIM 2
DIM 1

LINE

120VAC 60 Hz

16A MAX

 

 

 

15 Volvo Drive   Rockleigh, NJ 07647

 

Tel: 888.CRESTRON

 

Fax: 201.767.7576

Specifications subject to 

www.crestron.com

change without notice.