Maxus mxn102 ユーザーズマニュアル
6
MXN102
Operating Instructions
Interchange Information
Can use 5/8” to 2” 18 gauge brad nails designed for the following tools: Bostitch® BT125SK-2 & BT200K-2, Campbell
Hausfeld®NB0030 & NB0040, DeWalt® D51238K, Paslode® T125-F18 & T200-F18, Porter Cable® BN125 & BN200, and Senco
Finish Pro® 15 & 18.
Hausfeld®NB0030 & NB0040, DeWalt® D51238K, Paslode® T125-F18 & T200-F18, Porter Cable® BN125 & BN200, and Senco
Finish Pro® 15 & 18.
1
1
MPA
bar
psi
bar
psi
1
1
7
.
.
.
.
5
9
1
6
8
1
1
3
4
1
Recommended Hookup
Quick
Plug
Quick
Coupler
Air
Hose
Quick Plug
(Optional)
Quick
Coupler
(Optional)
Filter - Regulator
3
General Safety
Information
Information
(Continued)
Always assume the nailer contains
nails. Respect the tool as a working
implement; no horseplay. Always
keep others at a safe distance from
the work area in case of accidental
discharge of nails. Do not point the
tool toward yourself or anyone
whether it contains fasteners or not.
Accidental triggering of the nailer
could result in death or serious per-
sonal injury.
implement; no horseplay. Always
keep others at a safe distance from
the work area in case of accidental
discharge of nails. Do not point the
tool toward yourself or anyone
whether it contains fasteners or not.
Accidental triggering of the nailer
could result in death or serious per-
sonal injury.
Do not drive a
nail on top of
other nails. The
nail could glance
and cause death
or a serious punc-
ture wound.
other nails. The
nail could glance
and cause death
or a serious punc-
ture wound.
Do not operate
or allow anyone
else to operate
the nailer if any
warnings or
warning labels
are not legible.
Warnings or warning labels are locat-
ed on the nailer magazine and body.
else to operate
the nailer if any
warnings or
warning labels
are not legible.
Warnings or warning labels are locat-
ed on the nailer magazine and body.
Do not drop or throw the tool.
Dropping or throwing the tool can
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown, exam-
ine the tool closely for bent, cracked
or broken parts and air leaks. STOP
and repair before using or serious
injury could occur.
result in damage that will make the
tool unusable or unsafe. If the tool
has been dropped or thrown, exam-
ine the tool closely for bent, cracked
or broken parts and air leaks. STOP
and repair before using or serious
injury could occur.
Caution indicates
a potentially haz-
a potentially haz-
ardous situation which, if not avoided,
MAY result in minor or moderate
injury.
MAY result in minor or moderate
injury.
!
CAUTION
Operating The Nailer
RECOMMENDED HOOKUP
The illustration below shows the
recommended hookup for the nailer.
recommended hookup for the nailer.
1. The air com-
pressor must
be able to
maintain a
minimum of 60
psi when the nailer is being used. An
inadequate air supply can cause a
loss of power and inconsistent
driving.
be able to
maintain a
minimum of 60
psi when the nailer is being used. An
inadequate air supply can cause a
loss of power and inconsistent
driving.
2. Always use air supply hoses with a
minimum working pressure rating
equal to or greater than the pres-
sure from the power source if a reg-
ulator fails, or 150 psi, whichever is
greater. Use 3/8” air hose for runs
up to 50’. Use 1/2” air hoses for 50’
run or longer. For better perfor-
mance, install a 3/8” quick plug (1/4”
NPT threads) with an inside diame-
ter of .315” (8mm) on the nailer and
a 3/8” quick coupler on the air hose.
equal to or greater than the pres-
sure from the power source if a reg-
ulator fails, or 150 psi, whichever is
greater. Use 3/8” air hose for runs
up to 50’. Use 1/2” air hoses for 50’
run or longer. For better perfor-
mance, install a 3/8” quick plug (1/4”
NPT threads) with an inside diame-
ter of .315” (8mm) on the nailer and
a 3/8” quick coupler on the air hose.
3. Use a pressure regulator on the
compressor, with an operating pres-
sure of 0 - 125 psi. A pressure regu-
lator is required to control the oper-
ating pressure of the nailer between
60 and 100 psi.
sure of 0 - 125 psi. A pressure regu-
lator is required to control the oper-
ating pressure of the nailer between
60 and 100 psi.
Do not make any modifications to the
tool without first obtaining written
approval from Maxus. Do not use the
nailer if any shields or guards are
removed or altered. Do not use the
nailer as a hammer. Personal injury or
tool
damage may occur.
approval from Maxus. Do not use the
nailer if any shields or guards are
removed or altered. Do not use the
nailer as a hammer. Personal injury or
tool
damage may occur.
Avoid long extended periods of
work with the nailer. Stop using the
nailer if you feel pain in hands or
arms.
nailer if you feel pain in hands or
arms.
Always check that the Work Contact
Element (WCE) is operating proper-
ly. A nail could accidentally be dri-
ven if the WCE is not working prop-
erly. Personal injury may occur (See
"Checking the Work Contact
Element" Section).
ly. A nail could accidentally be dri-
ven if the WCE is not working prop-
erly. Personal injury may occur (See
"Checking the Work Contact
Element" Section).
Disconnect air supply and release
tension from the pusher before
attempting to clear jams because
fasteners can be ejected from the
front of the nailer. Personal injury
may occur.
attempting to clear jams because
fasteners can be ejected from the
front of the nailer. Personal injury
may occur.
Notice indicates
important infor-
important infor-
mation, that if not followed, MAY
cause damage to equipment.
cause damage to equipment.
Avoid using the nailer when the
magazine is empty. Accelerated
wear on the nailer may occur.
wear on the nailer may occur.
Clean and check all air supply hoses
and fittings before connecting the
nailer to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
nailer to an air supply. Replace any
damaged or worn hoses or fittings.
Tool performance or durability may
be reduced.
NOTICE
MXN102
Operating Instructions
!
WARNING
60 psi
Min.
Min.
100 psi
Max.
Max.
150 psi or greater
3/8” I.D.
Notes