Country Flame CF-04 ユーザーズマニュアル
Version 2.0e
46
APPENDIX B: MAINTENANCE GUIDE
(CONT’D)
Replacing the Door / Glass Gaskets
To replace the gaskets, remove the door by lifting it
straight up off its hinge pins and laying it face down
on a soft surface. Remove the door gasket (you
may need to use pliers) and then remove the glass
retaining clips and remove glass. Strip off old
gasket around glass and clean glass well. Clean out
old stove gasket material from gasket track. Once
the door and glass are clean, apply gasket material
to glass surface and return glass to door, securing
with clips (Use care not to over-tighten). Then
apply a generous bead of gasket cement into the
track. Position the NEW gasket into track and
gently press into door. Trim off any excess gasket
and wipe away excess cement. Let the cement set
24 hours before placing door back on unit and using
the unit. Gasket material and cement may be
obtained from your dealer.
straight up off its hinge pins and laying it face down
on a soft surface. Remove the door gasket (you
may need to use pliers) and then remove the glass
retaining clips and remove glass. Strip off old
gasket around glass and clean glass well. Clean out
old stove gasket material from gasket track. Once
the door and glass are clean, apply gasket material
to glass surface and return glass to door, securing
with clips (Use care not to over-tighten). Then
apply a generous bead of gasket cement into the
track. Position the NEW gasket into track and
gently press into door. Trim off any excess gasket
and wipe away excess cement. Let the cement set
24 hours before placing door back on unit and using
the unit. Gasket material and cement may be
obtained from your dealer.
Replacing the Glass
Remove the door gasket (you may need to use
pliers) and then remove the glass retaining clips and
remove glass. Replacement glass should be 0.200”
(5mm) thick. Overall size of the glass is 16”
(405mm) wide by 11” (279mm) high, cut to an
irregular shape to fit the door front. Your unit uses
pliers) and then remove the glass retaining clips and
remove glass. Replacement glass should be 0.200”
(5mm) thick. Overall size of the glass is 16”
(405mm) wide by 11” (279mm) high, cut to an
irregular shape to fit the door front. Your unit uses
Euro Kera
or a similar ceramic type high temp
glass. Do not use any other than recommended
glass type in this unit. Replacement glass may be
obtained from your dealer. Clean out old stove
gasket material from gasket track. Once the area is
clean, apply gasket material to new glass surface
and return glass to door, securing with clips (Use
care not to over-tighten).
glass type in this unit. Replacement glass may be
obtained from your dealer. Clean out old stove
gasket material from gasket track. Once the area is
clean, apply gasket material to new glass surface
and return glass to door, securing with clips (Use
care not to over-tighten).
Adjusting the Doors
The doors of your Crossfire Stove may need some
adjustment due to shipping vibrations, jarring
during installation and extended use. It is important
that the Crossfire door fit properly and remain
airtight. Periodically check the alignment of the
doors. To adjust the door, loosen the Allen bolts in
the hinge and adjust the door accordingly. When
completed, use a piece of paper between the door
and the stove to ensure a proper seal. The paper
should not pull out easily once the door is closed
and latched.
adjustment due to shipping vibrations, jarring
during installation and extended use. It is important
that the Crossfire door fit properly and remain
airtight. Periodically check the alignment of the
doors. To adjust the door, loosen the Allen bolts in
the hinge and adjust the door accordingly. When
completed, use a piece of paper between the door
and the stove to ensure a proper seal. The paper
should not pull out easily once the door is closed
and latched.