ICOM id-rp2 ユーザーズマニュアル
1
SYSTEM OUTLINE
1
The D-star repeater site can be constructed by com-
bining with the following units according to the plan or
scale.
bining with the following units according to the plan or
scale.
ID-RP2C : Repeater controller
ID-RP2D : 1.2 GHz data repeater
ID-RP2V : 1.2 GHz digital voice repeater
ID-RP2L : 10 GHz microwave link repeater
ID-RP2D : 1.2 GHz data repeater
ID-RP2V : 1.2 GHz digital voice repeater
ID-RP2L : 10 GHz microwave link repeater
In addition, the following options are also required for
system repeater operations.
system repeater operations.
AH-106 : 10 GHz Parabolic antenna 800 (d)
AH-107 : 10 GHz Parabolic antenna 450 (d)
AH-108 : 1.2 GHz Collinear antenna
AH-107 : 10 GHz Parabolic antenna 450 (d)
AH-108 : 1.2 GHz Collinear antenna
■ ID-RP2C
➥The ID-RP2C is a repeater controller and one con-
troller should be used in each repeater site.
The controller relays digital voice or data
The controller relays digital voice or data
(traffic)
sig-
nals for repeater operation.
➥Total 4 interface connectors for local repeater con-
nections are available.
Both digital voice and data repeaters can be con-
nected as desired.
• Standard composition:
Both digital voice and data repeaters can be con-
nected as desired.
• Standard composition:
Data repeater 1
Digital voice repeater 1
Spares 2
Digital voice repeater 1
Spares 2
(for another band’s repeater)
NOTE: Connect only 1 or 2 repeaters for the
same frequency band is recommended
to avoid interference.
to avoid interference.
➥Total 2 interface connectors for microwave link re-
peater connections are available.
Microwave link repeater can be connected as de-
sired.
Microwave link repeater can be connected as de-
sired.
➥One Ethernet port
(10Base-T)
is available for re-
peater site call sign, IP address settings etc., from
the PC and the ID-RP2C utility software.
Or, a gateway control PC can be connected as de-
sired.
the PC and the ID-RP2C utility software.
Or, a gateway control PC can be connected as de-
sired.
➥By connecting the ID-RP2L utility installed PC, op-
erating frequency set and operation monitor can be
made.
made.
■ ID-RP2D
➥ID-RP2D is a 1.2 GHz data
(128 kbps)
repeater and
connects to the ID-RP2C.
*The ID-RP2D never functions as a repeater without ID-
RP2C, due to no relay function is built-in.
➥The ID-RP2D/V utility software, supplied with the ID-
RP2C, and a PC are required for both receive and
transmit frequency settings.
transmit frequency settings.
➥Repeater operation is performed in simplex mode on
the same frequency for data mode, however, differ-
ent frequencies between transmit and receive can
be set in simplex mode.
ent frequencies between transmit and receive can
be set in simplex mode.
■ ID-RP2V
➥ID-RP2V is a 1.2 GHz digital voice and slow-speed
data repeater
(4.8 kbps)
and connects to the ID-
RP2C.
*The ID-RP2V never functions as a repeater without ID-
RP2C, due to no relay function is built-in.
NOTE: No audio CODEC is performed in the ID-
RP2V, thus the ID-RP2V receives and
transmits 4.8 kbps serial data only.
transmits 4.8 kbps serial data only.
➥Different frequencies are used for each transmission
and reception in semi-duplex mode.
➥The ID-RP2D/V utility software, supplied with the ID-
RP2C, and a PC are required for both receive and
transmit frequency settings.
transmit frequency settings.
■ ID-RP2L
➥ID-RP2L is a 10 GHz microwave link repeater
(10
Mbps)
and connects to the ID-RP2C. The microwave
link repeater provides to linking with another re-
peater site
peater site
(Area)
for zone construction.
➥Different frequencies are used for each transmission
and reception in full-duplex mode and the reversed
frequencies between transmit and receive are used
for the oncoming repeater.
frequencies between transmit and receive are used
for the oncoming repeater.
➥The received GMSK serial bit-stream signal
(10
Mbps)
is applied to either ID-RP2D or ID-RP2V via
the ID-RP2C. Then the GMSK serial data is trans-
mitted to the local station.
mitted to the local station.
➥The ID-RP2L has a duplexer, and the condition of
the microwave link repeater can be monitored when
the ID-RP2L utility software
the ID-RP2L utility software
(supplied with the ID-
RP2C)
installed PC is connected to the ID-RP2C.