Zenith c27h26b ユーザーズマニュアル

the display from the screen, press this button again. This 
button is also the “–” button used when selecting digital 
channels.

 4. SLEEP Button - To set the TV to turn off after a preset  

amount of time, press the SLEEP button. The clock will 
count up 10 minutes each time the button is pressed in the
order of 0, 10, 20, ...100, 110, 120. After the sleep time is
programmed, the display will disappear then reappear 
momentarily every ten minutes to remind you the sleep timer 
function is operating. To confi rm the sleep time setting, 
press the SLEEP button once and the remaining time will 
be momentarily displayed. To cancel sleep time, press the 
SLEEP button repeatedly until the display turns to 0.

  5.  VOL (VOLUME) + / – Buttons - Press the “+” button to   

increase, or the “–” button to decrease the volume level. 
Use to select the desired setting during the menu screen 
operation.

 6. MENU/ENTER Button - Press to display the menu screen. 

While in the on-screen menu, press to enter or select 
options.

  7.  EXIT Button - Press to exit the menu screen.
 8.  

TV/AV Button - Press this button to display SOURCE  
SELECTION menu to select the video input source.

  9.  QUICK VIEW Button - This button allows you to go back to
 

  the previous channel selected by pressing the QUICK VIEW 

button. Press this button again to return to the channel you 
were watching. 

 10.  MUTE Button - To turn off the sound, press this button once.

The TV will be silenced and the symbol “MUTE” will appear 
on the screen. The muting feature can be released by pressing 
the MUTE button again or one of the VOL + or – buttons.

 Buttons - Press the 

 button to

 

  change to a higher numbered channel set into memory.

 

  Press the 

 button to change to a lower numbered channel 

set into memory. Use to select the desired setting during 
the menu screen operation.

 12.  PICTURE SIZE Button - Press to change the picture size.
 13. AUDIO Button - Press to select the desired audio setting.
 14.  CLOSED CAPTION Button - Press this button to display 

CLOSED CAPTION menu.

 15.  ANALOG/DIGITAL Button - Press to select analog/digital mode.

- Press to turn the power on/off to the TV. 

  2.  Direct Channel Selection Buttons (0-9) - Allow direct 

access to any channel.

- When the TV is receiving an analog 

signal pressing this button will display the current 
information on-screen. When the TV is receiving a 
digital signal, pressing this button once will display the 
digital information on-screen; pressing it a second time 
will display the analog information on-screen. To remove 

Before using the remote control, batteries must fi rst be installed.

1. Open the battery compartment cover.

2. Install two “AAA” batteries (not supplied).

3. Replace the battery compartment cover.

Use two “AAA” size batteries (not supplied). The batteries 
may last approximately one year depending on how much 
the remote control is used. For best performance, it is 
recommended that batteries should be replaced on a yearly 
basis, or when the remote operation becomes erratic. Do not 
mix old and new batteries or different types. 

These precautions should be followed when using batteries
in this device:
•  Use only the size and type of batteries specifi ed.
•  Be sure to follow the correct polarity when installing the 

batteries as indicated in the battery compartment.  
Reversed batteries may cause damage to the device.

•  Do not mix different types of batteries together (e.g. Alkaline 

and Carbon-zinc) or old batteries with fresh ones.

•  If the device is not to be used for a long period of time, 

remove the batteries to prevent damage or injury from 
possible battery leakage.

•  Do not try to recharge batteries not intended to be recharged; 

they can overheat and rupture (follow battery manufacturer’s 
directions).

J33A0621B_EN.indb   7

J33A0621B_EN.indb   7

1/31/08   5:30:53 PM

1/31/08   5:30:53 PM