Hayward Pools sp3207ec ユーザーズマニュアル

®

P/N-IS3200-HC-07

INSTALLATION, OPERATION, & PARTS

The Hayward TriStar Pump is Specifically Engineered for the demanding requirements of today’s in-ground 

swimming pool/spa that is equipped with large capacity filters, heaters, and pool cleaning equipment. The 

TriStar is a self-priming pump that incorporates an improved seal and impeller design that will provide many 

years of efficient, dependable, corrosion-free service. The advanced design provides superior performance 

while reducing maintenance requirements. NOTE - To prevent potential injury and to avoid unnecessary 

service calls, read this manual carefully and completely.

 - The TriStar is a high performance, high efficiency 

pump. When replacing most existing pumps, you can use a 

2880 Plymouth Drive, Oakville, ON L6H 5R4

TEL: (905) 829-2880

WWW.HAYWARDCANADA.COM            USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

This product should be installed and serviced only by a qualified professional.

A Licensed electrician MUST complete, in full, all electrical installations noted in this manual.

Before installing or servicing this electrical equipment, turn power supply OFF.

Basic safety percautions should always be followed, including the following: Failure to follow instructions may result in injury.

       This is the safety-alert symbol. When you see this symbol on your pump or in this manual, look for one of the following 

signal words and be alert to the potential for personal injury.

 warns about hazards that will cause serious potential injury, death or major property damage and if 

ignored presents an imminent hazard.

 warns about hazards that could cause serious personal injury, death or major property damage and if 

ignored presents a potential hazard.

 warns about hazards that will or can cause minor or moderate personal injury and/or property damage 

and if ignored presents a potential hazard. It can also make consumers aware of actions that are unpredictable and unsafe.

The NOTICE label indicated special instructions that are important but not related to hazards.

    WARNING

 - To reduce risk of injury, do not permit children to use or climb on this product. Closely supervise 

children at all times. Components such as the filtration system, pumps, and heaters must be positioned to prevent children 

from using them as means of access to the pool.

    CAUTION

 - This pump is intended for use on permanently installed swimming pools and may also be used with 

hot tubs and spas if so marked. Do NOT use with storable pools. A permanently installed pool is constructed in or on the 

ground or in a building such that it cannot be readily disassembled for storage. A storable pool is constructed so that it is 

capable of being readily disassembled for storage and reassembled to its original integrity. Though this product is designed for 

outdoor use, it is strongly advised to protect the electrical components from the weather. Select a well-drained area, one that 

will not flood when it rains. It requires free circulation of air for cooling. Do not install in a damp or non-ventilated location. If 

installed within an outer enclosure or beneath a skirt of a hot tub or spa, adequate ventilation and free circulation of air must 

be provided to prevent overheating of the motor.

    WARNING

 - Pool and spa components have a finite life. All components should be inspected frequently and 

replaced at least every ten years, or if found to be damaged, broken, cracked, missing, or not securely attached. 

WWW.HAYWARDCANADA.COM            USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

WWW.HAYWARDCANADA.COM            USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

      

 - 

electrical wiring. Hazardous voltage. Can shock, burn, or cause death. To reduce the risk of electrical shock, do 

NOT use an extension cord to connect unit to electric supply. Provide properly located outlet. All electrical wiring 

MUST be in conformance with applicable local and national codes and regulations. Before working on pump or 

motor, disconnect motor wiring.

 - 

To reduce the risk of electrical shock replace damaged cord immediately. Do NOT bury cord. Locate cord to 

prevent abuse from lawn mowers, hedge trimmers and other equipment.

 - 

Connect only to a grounding type receptacle protected by a Ground Fault Circuit Interrupter (GFCI). 

Contact a licensed electrician if you cannot verify that the receptacle is protected by a GFCI.

 -

 Failure to bond pump to pool structure will increase risk of electrocution and could result in injury or death. To 

reduce the risk of electrical shock, see installation instructions and consult a professional electrician on how to bond pump. Also, contact a 

licensed electrician for information on local electrical codes for bonding requirements.

Use a solid copper conductor, size 6 or larger. Run continuous wire from external bonding lug to reinforcing rod or mesh. Connect a No. 6 

AWG solid copper bonding wire to the pressure wire connector provided on the motor housing and to all metal parts of swimming pool, spa, 

or hot tub, and to all the electrical equipment, metal piping (except gas piping), and conduit within 5 ft. (1.5 m) of inside walls of swimming 

pool, spa, or hot tub. IMPORTANT - Reference Canadian Electrical Codes for all wiring standards including, but not limited to grounding, 

bonding and other general wiring procedures.

 - 

Suction in suction outlets and/or suction outlet covers which are damaged, broken, cracked, missing, or 

unsecured cause sever injury and/or death due to the following entrapment hazards:

Hair Entrapment - Hair can become entangled in suction outlet cover.

Limb Entrapment - A limb inserted into an opening of a section outlet sump or suction outlet cover that is 

damaged, broken, cracked, missing, or not securely attached can result in a medical bind or swelling of the 

limb.

Body Suction Entrapment - A differential pressure applied to a large portion of the body or limbs can result in an entrapment.

Evisceration/Disembowelment - A negative pressure applied directly to the intestines through an unprotected suction outlet 

sump or suction outlet cover which is damaged, broken, cracked, missing, or unsecured can result in 

evisceration/disembowelment.

Mechanical Entrapment - There is potential for jewelry, swimsuits, hair decorations, fingers, toes, or knuckles to be caught in 

an opening of a suction outlet cover resulting in mechanical entrapment.

 - 

- When outlets are small enough to be blocked by a person, a minimum of two functioning suction outlets per 

pump must be installed. Suction outlets in the same place (i.e. floor or wall), must be installed a minimum of 

three feet (3’) [0.91 meter] apart, as measured from near point to near point.

- Dual suction fittings shall be placed in such locations and distanced to avoid “dual blockage” by a user.

- Dual suction fittings shall not be located on seating areas or on the backrest for such seating areas.

- The maximum system flow rate shall not exceed the values shown in the “Pipe Sizing Chart” found at the bottom of page 4 of this manual

- Never use pool or spa if any suction outlet component is damaged, broken, cracked, missing, or not securely attached.

- Replace damaged, broken, cracked, missing, or not securely attached suction outlet components immediately.

- In addition to two or more suction outlets per pump installed in accordance with the latest IAF (formerly NSPI) standards and CPSC 

guidelines, follow all national, state, and local codes applicable.

- Installation of a vacuum release or vent system, which relieves entrapping suction, is recommended.

WWW.HAYWARDCANADA.COM            USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

8.43

10.18

“A”

13.61

8.16

11.53

7.63

8.74

3/4

1

1 1/2

2
3

12-3/32”

12-19/32”

13-3/32”
13-3/32”
15-3/32”

 - 

This product should be installed and serviced only by a qualified professional.

Locate pump as close to pool as practical and run suction lines as direct as possible to reduce friction loss. 

Suction lines should have continuous slope upwards from lowest point in line. Joints must be tight (but not 

over-tightened). Suction line diameter must equal or be larger than the discharge diameter.

                                   Though the pump is designed for outdoor use, it is strongly advised to protect the electrical components 

from the weather. Select a well-drained area, one that will not flood when it rains. Do NOT install pump in a damp or 

non-ventilated location. Keep motor clean. Pump motors require free circulation from air for cooling.

Install pump on a firm, level base or pad to meet all local and national codes.  Fasten pump to base or pad with screws or bolts to 

further reduce vibration and stress on pipe or hose joints.  The base MUST be solid, level, rigid, and vibration free.

Allow pump inlet height to be as close to water level as possible.

Allow use of short, direct suction pipe (to reduce friction losses).

Allow for gate valves in suction and discharge piping.

Be protected from excess moisture and flooding.

Allow adequate access for servicing pump and piping.

NOTE - It is recommended that a minimum length of piping, equivalent to 10 pipe diameters, be used between the 

pump suction inlet and any plumbing fittings.

 

Pipe Size 

[mm] 

Flow Rate 

GPM [L PM] 

Suction Pipe 

L ength * 

Pipe Size 

[mm] 

Flow Rate 

GPM [L PM] 

Suction Pipe 

L ength * 

Pipe Size 

[mm] 

Flow Rate 

GPM [L PM] 

Suction Pipe 

L ength * 

1”   [32] 

20  [75] 

5” 

1 ½”   [50] 

45  [170] 

7 ½”  

2 ½”   [75] 

110  [415] 

12 ½”  

1 ¼”   [40] 

30  [110] 

6 ¼”  

2”   [63] 

80  [300] 

10” 

3”   [90] 

160  [600] 

15” 

 

WWW.HAYWARDCANADA.COM            USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

 - 

Hazardous Pressure. Pumps, filters, and other equipment/components of a swimming pool 

filtration system operate under pressure. Incorrectly installed and/or improperly tested filtration equipment and/or components 

may fail resulting in injury and/or property damage.

Use Teflon tape to seal threaded connections on molded plastic components. All plastic fittings must be new or thoroughly cleaned before 

use. NOTE - Do NOT use Plumber’s Pipe Dope as it may cause cracking to the plastic components. When applying Teflon tape to 

plastic threads, wrap the entire threaded portion of the male fitting with one to two layers of tape. Wind the tape clockwise as you face the 

open end of the fitting, beginning at the end of the fitting. The pump suction and outlet ports have molded-in thread stops. Do NOT attempt 

to force hose connector fitting past this stop. It is only necessary to tighten fittings enough to prevent leakage. Tighten fitting by hand and 

then use a tool to engage fitting an additional 1 ½ turns. Use care when using Teflon tape as friction is reduced considerable; do NOT 

over-tighten fitting or you may cause damage. If leaks occur, remove connector, clean off old Teflon tape, re-wrap with one or two 

additional layers of Teflon tape, and re-install connector.

Fittings restrict flow. For better efficiency, use the fewest possible fittings (but at least two suction outlets). Avoid fittings that could cause 

an air trap. Pool and spa fittings MUST conform to the International Association of Plumping and Mechanical Officials (IAPMO) 

standards. Use a non-entrapping suction fitting in pool (multiple drains) or double suction (skimmer and main drain).

 - 

Ground and bond motor before connecting to electrical power supply. Failure to ground and 

bond pump motor can cause serious or fatal electrical shock hazard.

 - 

Do NOT ground to a gas supply line.

 - 

To avoid dangerous or fatal electrical shock, turn OFF power to motor before working on 

electrical connections.

 - 

Ground Fault Circuit Interrupter (GFCI) tripping indicates electrical problem. If GFCI trips and 

wont reset, consult electrician to inspect and repair electrical system.

 - 

Fire Hazard. Match supply voltage to motor nameplate voltage.

Insure that the electrical supply available agrees with the motor’s voltage, phase, and cycle, and that the wire size is adequate for the H.P. 

(KW) rating and distance from the power source. NOTE - All electrical wiring MUST be performed by a licensed electrician, and 

MUST conform to local codes and Canadian Electrical Code regulations. Use copper conductors only. 

 

M otor  B r ake H or sepower 

M otor  Rated H or sepower 

 

 

H P  (kW ) 

H P  (kW ) 

V oltage 

Amps 

AW G 

Amps 

1.13  (0.84) 

0.50  (0.37) 

208 - 230 / 115 

5.3 - 4.9 / 9.8 

14 

10 / 15 

1.39  (1.04) 

0.75  (0.56) 

208 - 230 / 115 

7.0 - 6.2 / 12.4 

14 

10 / 15 

1.85  (1.38) 

1.00  (0.75) 

208 - 230 / 115 

8.5 - 7.4 / 14.8 

14 / 12 

15 / 20 

2.40  (1.79) 

1.50  (1.12) 

208 - 230 / 115 

11.2 - 10.2 / 20.4 

14 / 10 

15 / 30 

2.70  (2.01) 

2.00  (1.49) 

208 - 230 

11.8 - 11.0 

14 

15 

3.60  (2.69) 

3.00  (2.24) 

208 - 230 

16.0 - 14.8 

12 

20 

3.60  (2.69) * 

3.00  (2.24) * 

208 - 230 / 460 * 

9.6 - 9.4 / 4.7 * 

14 * 

15 / 10 * 

1.85 / 0.22  (1.38 / 0.16) 

1.00 / 0.12  (0.75 / 0.09) 

208 - 230 

8.6 - 8.2 1 

14 

15 

2.40 / 0.28  (1.79 / 0.21) 

1.50 / 0.18  (1.12 / 0.13) 

208 - 230 

11.4 - 10.4 2 

14 

15 

ps 

2.70 / 0.33  (2.01 / 0.25) 

2.00 / 0.25  (1.49 / 0.19) 

208 - 230 

12.4 - 11.2 3 

14 

15 

0.94  (0.70) 

0.75  (0.56) 

 

5.4 / 10.8 

14 

10 / 15 

1.25  (0.93) 

1.00  (0.75) 

230 / 115 

7.0 / 14.0 

14 

10 / 15 

1.65  (1.23) 

1.50  (1.12) 

230 / 115 

7.7 / 15.4 

14 / 12 

10 / 20 

2.20  (1.64) 

2.00  (1.49) 

230 / 115 

10.8 / 21.6 

14 / 10 

15 / 30 

2.60  (1.94) 

2.50  (1.86) 

230 

11.5 

14 

15 

3.45  (2.57) 

3.00  (2.24) 

230 

13.5 

14 

15 

1.85 / 0.22  (1.38 / 0.16) 

1.50 / 0.18  (1.12 / 0.13) 

208 - 230 

8.6 - 8.2 1 

14 

15 

2.40 / 0.28  (1.79 / 0.21) 

2.00 / 0.25  (1.49 / 0.19) 

208 - 230 

11.4 - 10.4 2 

14 

15 

ps 

2.70 / 0.33  (2.01 / 0.25) 

2.50 / 0.31  (1.86 / 0.23) 

208 - 230 

12.4 - 11.2 3 

14 

15 

1 2

, 

-

  - 

-

 

    

-

-

 

 

¹, ², ³  Low Speed Amps:  (¹ 2.8 - 3.0) (² 3.2 - 3.4) (³ 3.8 - 4.1)

*      Three-Phase (3Φ) Pump - motor starter required

WWW.HAYWARDCANADA.COM            USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

16

17

18

15

14

13

12

11

10

7

8

9

20

21

22

6

5

4

3

2

1

19

16

SPX3200UNKIT
SPX3200UG
SPX3200A
SPX3200DLS
SPX3200S
SPX3200M
SPX3200Z8
SPX4000Z1
SPX3200B3
SPX3200Z1
SPX3021R

Union Connector Kit (Nut, Connector, Gasket)
Union Gasket (T-seal), 50 duro EPDM
Pump Strainer Housing, 2” x 2” with Drain Plugs, threaded style
Strainer Cover Kit (Includes Strainer Lexan Cover, Lock Ring, O-Ring)
Strainer Cover O-Ring
Strainer Basket
Diffuser Screw
Diffuser O-Ring
Diffuser, 3 HP
Impeller Screw
Impeller Ring

1
1
1

10
10
15

1

10

1
1
1

Detail of motor 

canopy with screws.

WWW.HAYWARDCANADA.COM            USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

 - All wiring must be done by a licensed electrician.

Voltage at motor MUST NOT be more than 10% above or below motor name place rated voltage, or motor may overheat, causing overload tripping 

and reduced component life. If voltage is less than 90% or more than 110% of rated voltage when motor is running at full load, consult power 

company.

Install, ground, bond, and wire motor is accordance with local or Canadian Electrical Code requirements.

Permanently ground motor. Use green ground terminal provided under motor canopy or access place; use size and type wire required by code. Connect 

motor ground terminal to electrical service ground.

Bond motor to pool structure. Bonding will connect all metal parts within and around the pool with a continuous wire. Bonding reduces the risk of a 

current passing between bonded metal objects, which could potentially cause electrical shock if grounded or shorted. Reference Canadian Electrical 

Use a solid copper conductor, size 6 or larger. Run wire from external bonding lug to reinforcing rod or mesh. Connect a No. 6 AWG solid copper 

bonding wire to the pressure wire connector provided on the motor housing and to all metal parts of swimming pool, spa, or hot tub, and to all 

electrical equipment, metal piping (except gas piping), and conduit within 5 ft. (1.5 m) of inside walls of swimming pool, spa, or hot tub.

Pump MUST be permanently connected to circuit. If other lights or appliances are also on the same circuit, be sure to add their amp loads before 

calculating wire and circuit breaker sizes. Use the load circuit breaker as the Master On-Off switch,

Install a Ground Fault Circuit Interrupter (GFCI) in circuit; it will sense a short-circuit to ground and disconnect power before it becomes dangerous 

to pool users. For size of GFCI required and test procedures for GFCI, see manufacture’s instructions. In case of a power outage, check GFCI for 

tripping, which will prevent normal pump operation. Reset if necessary.

WWW.HAYWARDCANADA.COM            USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

SP3207EC

SPX3207Z1BER

SPX3207C

SP3210EC

SPX3210Z1BER

SPX3210C

SP3215EC

SPX3215Z1BER

SPX3215C

SP3220EC

SPX3220Z1BER

SPX3220C

SP3230EC

SPX3230Z1BER

SPX3230C

SP32102EC

SPX3210Z2BER

SPX3210C

SP32152EC

SPX3215Z2BER

SPX3215C

SP32202EC

SPX3220Z2BER

SPX3220C

12

13
14
15
16
17
18
19
20

21 *
22 *

SPX3207C
SPX3210C
SPX3215C
SPX3220C
SPX3230C
SPX3200SA
SPX3200T
SPX3200E
SPX3200Z211
SPX3200Z3
SPX3200Z5
SPX4000FG
SPX3200GA
SPX3200WF
SPX3200SR

Description
Impeller for ¾ HP with Impeller Screw
Impeller for 1 HP with Impeller Screw
Impeller for 1 ½ HP with Impeller Screw
Impeller for 2 HP with Impeller Screw
Impeller for 3 HP with Impeller Screw
Shaft Seal Assembly
Housing O-Ring
Seal Plate
Housing Insert & Seal Place Spacer Kit
Housing Bolt
Motor Bolt
Drain Plug with O-Ring
Motor support Bracket
Riser Base, Short
Riser Base, Tall

10
10
10
10
10
10
10

1
1

10

1

10

1
1
1