Roper w10150599a ユーザーズマニュアル

■

 The top of the agitator is much 

higher than the highest water level. This is normal and 
necessary for clothes to move freely. 

■

 Replace the fuse or reset the circuit breaker. If the 

problem continues, call an electrician.

■

Is the washer in a normal pause in the cycle? The washer 
pauses for about 2 minutes during certain cycles. Allow the 
cycle to continue. Some cycles feature periods of agitation and 
soak. 

■

Is the washer overloaded? Wash smaller loads.

■

Is the lid open? The lid must be closed during operation. 
Washer will not agitate or spin with the lid open.

■

 See the Installation 

Instructions for proper installation of drain hose.

■

Is the lid open? The lid must be closed during operation. 
Washer will not agitate or spin with the lid open.

■

Is there excessive sudsing? Always measure detergent. 
Follow manufacturer’s directions. If you have very soft water, 
you might need to use less detergent.

■

Is the top of drain hose lower than the water level in washer? 
The top of the hose must be higher than the water level in the 
washer for proper operation. See the Installation Instructions.

■

 The drain hose should be loose yet fit 

securely. Do not seal the drain hose with tape. The hose needs 
an air gap. See the Installation Instructions.

■

Are the hot and cold water inlet hoses reversed? See the 
Installation Instructions for more information. As your frequency 
of loads washed increases, the water temperature may 
decrease for hot and warm temperatures. This is normal.

■

Did you use the right cycle for the load being washed?
Select a cycle with a higher spin speed (if available).

■

Did you use a cold rinse? Cold rinses leave loads wetter than 
warm rinses. This is normal.

■

Did you sort properly? Sort lint givers (towels, chenille) from 
lint takers (corduroy, synthetics). Also sort by color.

■

Did you overload the washer? The wash load must be 
balanced and not overloaded. Clothes should move freely. Lint 
can be trapped in the load if overloaded. Wash smaller loads.

■

Did you select the correct water level? The water level 
should be correct for the load size. Clothes should move freely 
in the water.

■

Did you use enough detergent? Follow manufacturer’s 
directions. Use enough detergent to hold the lint in the water.

■

Did you line dry your clothing? If so, you can expect some lint 
on the clothing.

■

Was paper or tissue left in the pockets?

Is your water colder than 60°F (15.6°C)? Wash water colder 
than 60°F (15.6°C) may not completely dissolve the detergent.

Did you use the proper cycle time for the load? Reducing 
wash time (duration) is another way to reduce lint.

■

 Measure detergent and fabric 

softener. Use enough detergent to remove soil and hold it in 
suspension. Dilute fabric softener and add to the rinse portion 
of a cycle only. Do not drip fabric softener on clothes.

■

Is there above average iron (rust) in water? You may need to 
install an iron filter.

■

Did you properly sort the load? Sort dark clothes from whites 
and lights.

■

Did you unload the washer promptly? To avoid the transfer of 
dye, unload the washer as soon as it stops.

■

Did you unload the washer promptly? Unload the washer as 
soon as it stops.

■

Did you use the right cycle for the load being washed?
Use the cycle for Casual or Permanent Press clothes or another 
cycle with low spin speeds (if available) to reduce wrinkling.

■

Did you overload the washer? The wash load must be 
balanced and not overloaded. Loads should move freely during 
washing.

To reduce wrinkling of permanent press clothes and some 
synthetic knits, use a large load size to provide more space.

■

Are the hot and cold water hoses reversed? Check that the 
hot and cold water hoses are connected to the right faucets. 
See the Installation Instructions.

■

Did you overload the washer? The wash load must be 
balanced and not overloaded. Loads should move freely during 
washing.

■

Did you wrap items around the agitator? Drop items loosely 
into the washer. Do not wrap items around the agitator.

■

Did you properly sort the load? Transfer of dye can occur 
when mixing whites and colors in a load. Sort dark clothes from 
whites and lights.

■

Was the wash temperature too low? Use hot or warm 
washes if safe for the load. Make sure your hot water system is 
adequate to provide a hot water wash.

■

Did you use enough detergent, or do you have hard water? 
Use more detergent for washing heavy soils in cold or hard 
water.

■

Are the hot and cold water hoses reversed? Check that the 
hot and cold water hoses are connected to the right faucets. 
See the Installation Instructions.