Vertex Standard FT-2000 ユーザーズマニュアル
Page 46
FT-2000 O
PERATING
M
ANUAL
“MY B
ANDS
” O
PERATION
When operating on an Amateur Band, it is possible to use the [BAND] buttons to engage the use of the [SUB VFO-B] knob
for Amateur band selection. The “My Bands” feature allows you to select several Amateur bands, and make only those
bands available for selection via the [SUB VFO-B] knob.
for Amateur band selection. The “My Bands” feature allows you to select several Amateur bands, and make only those
bands available for selection via the [SUB VFO-B] knob.
This feature can be very useful in a contest, where the 10/18/24 MHz band are not used, or if you do not have antennas for
some bands.
some bands.
“My Bands” Setup
1. Press the [MENU] button to engage the Menu mode.
2. Rotate the Main Tuning Dial knob to select Menu item
2. Rotate the Main Tuning Dial knob to select Menu item
“122 tun MY BAND.”
3. Rotate the [SUB VFO-B] knob to choose a band that
you wish to skip (omit) from the band-selection loop
(when using the [SUB VFO-B] knob for band selec-
tion). The available choices are 1.8/3.5/5/7/10/14/18/
21/24/28/50/GE (General Band)/AU (Transverter).
(when using the [SUB VFO-B] knob for band selec-
tion). The available choices are 1.8/3.5/5/7/10/14/18/
21/24/28/50/GE (General Band)/AU (Transverter).
4. Press the [ENT] button to set the omission command
to ON. The “E” (Enable) notation at the right of the
band notation will change to “d” (disable).
band notation will change to “d” (disable).
5. Repeat steps 3 and 4 to select/deselect as many bands
as you like.
N
N
OTE
:
The “ON” command sets the selected band to be
skipped, while the “OFF” command sets the selected
band to be included in the band-selection list. Return
the “d” notation to “E” to restore operation on a previ-
ously-deleted band.
skipped, while the “OFF” command sets the selected
band to be included in the band-selection list. Return
the “d” notation to “E” to restore operation on a previ-
ously-deleted band.
6. Press and hold in the [MENU] button for two seconds
to lock in the new configuration and exit to normal
operation.
operation.
C
ONVENIENCE
F
EATURES
Main Tuning Dial knob
[SUB VFO-B] Knob
[MENU] Button
[ENT] Button
[SUB VFO-B] Knob
(VFO-A)[BAND] Button
[A/B] Button
(VFO-B)[BAND] Button
14 MHz
14 MHz
18 MHz
18 MHz
50 MHz
21 MHz
21 MHz
7 MHz
7 MHz
5 MHz
1.8 MHz
28 MHz
28 MHz
24 MHz
3.5 MHz
3.5 MHz
10 MHz
14 MHz
21 MHz
7 MHz
28 MHz
3.5 MHz
A
DVICE
:
The “My Band” feature affects both the Main (VFO-A)
and Sub (VFO-B) bands.
and Sub (VFO-B) bands.
“My Band” Operation
1. Press the (VFO-A) [BAND] button; the imbedded LED
will glow Red, if you operate the “My Band” feature
on the Main band (VFO-A).
A
on the Main band (VFO-A).
A
DVICE
:
If the “My Band” feature on the Main band (VFO-A)
seems not to be operating, check see if the orange lamp
to the right of the [SUB VFO-B] knob is illuminated.
If so, pressing the [A/B] key will cause the orange lamp
to the right of the [SUB VFO-B] knob to go out. Now,
press the (VFO-A) [BAND] button to begin “My Band”
feature.
seems not to be operating, check see if the orange lamp
to the right of the [SUB VFO-B] knob is illuminated.
If so, pressing the [A/B] key will cause the orange lamp
to the right of the [SUB VFO-B] knob to go out. Now,
press the (VFO-A) [BAND] button to begin “My Band”
feature.
2. Press the (VFO-B) [BAND] button; the imbedded LED
will glow Orange, if you operate the “My Band” fea-
ture on the Sub band (VFO-B).
ture on the Sub band (VFO-B).
3. Rotate the [SUB VFO-B] knob to choose the Ama-
teur band on which you wish to operate. Only those
Amateur bands that have not been skipped will appear
as you scroll through the bands.
Amateur bands that have not been skipped will appear
as you scroll through the bands.