Vertex Standard FT-2000 ユーザーズマニュアル
Page 77
FT-2000 O
PERATING
M
ANUAL
T
RANSMITTER
C
ONVENIENCE
F
EATURES
S
PLIT
-F
REQUENCY
O
PERATION
1. Start with regular transceiver op-
eration on the Main (VFO-A) band.
MAIN (VFO-A)
MAIN (VFO-A)
[RX] switch “ON” (LED glows
Green)
[TX] switch “ON” (LED glows
Red)
SUB (VFO-B)
SUB (VFO-B)
[RX] switch “OFF” (LED Off)
[TX] switch “OFF” (LED Off)
[TX] switch “OFF” (LED Off)
2. Press and hold in the [SPLIT] button for two sec-
onds to engage the Quick Split feature, and apply a
frequency 5 kHz above the Main (VFO-A) fre-
quency to the Sub (VFO-B) frequency register.
Press and hold in the [SPLIT] button for two sec-
onds to increment the Main (VFO-A) frequency to
+5 kHz.
frequency 5 kHz above the Main (VFO-A) fre-
quency to the Sub (VFO-B) frequency register.
Press and hold in the [SPLIT] button for two sec-
onds to increment the Main (VFO-A) frequency to
+5 kHz.
The VFO configuration will then be:
MAIN (VFO-A)
[RX] switch “ON” (LED glows Green)
[TX] switch “OFF” (LED Off)
[TX] switch “OFF” (LED Off)
SUB (VFO-B)
[RX] switch “OFF” (LED Off)
[TX] switch “ON” (LED glows Red)
[TX] switch “ON” (LED glows Red)
Q
UICK
P
OINTS
:
The operating mode applied to the Sub (VFO-B)
register will be the same as that in use on the Main
(VFO-A) register.
(VFO-A) register.
The offset of the Sub (VFO-B) from the Main VFO
(VFO-A) is programmed via the Menu, and is set
to +5 kHz at the factory. Other offsets may be se-
lected, however, using the following procedure:
to +5 kHz at the factory. Other offsets may be se-
lected, however, using the following procedure:
1. Press the [MENU] button to enter the Menu mode.
2. Rotate the Main Tuning Dial knob to select Menu
2. Rotate the Main Tuning Dial knob to select Menu
item “031 gene Q SPLIT.”
3. Rotate the [SUB VFO-B] knob to select the de-
sired offset.
The available selections are –20kHz ~ +20kHz
(factory default: +5 kHz).
4. When you have completed all adjustments, press
and hold in the [MENU] button for two seconds to
save the new setting and exit to normal operation.
If you only press the [MENU] button momentarily
to exit, any changes you performed will not be
stored.
save the new setting and exit to normal operation.
If you only press the [MENU] button momentarily
to exit, any changes you performed will not be
stored.
[SPLIT] Button
MAIN [TX] Switch
Sub [RX] Switch
MAIN [RX] Switch
Sub [TX] Switch
Main Tuning Dial Knob
[SUB VFO-B] Knob
[MENU] Button
Quick Split Operation
The Quick Split feature allows you to set a one-touch offset of +5 kHz to be applied to your radio’s transmit
frequency on the Sub (VFO-B), compared to the Main (VFO-A) frequency.
frequency on the Sub (VFO-B), compared to the Main (VFO-A) frequency.