FMI VMH26TPC ユーザーズマニュアル
www.fmiproducts.com
113111-01
23
CleanIng and MaInTenanCe
4. Check injector holder located at end of
burner tube again. Remove any large
particles of dust, dirt, lint, or pet hair with
a soft cloth or vacuum cleaner nozzle.
particles of dust, dirt, lint, or pet hair with
a soft cloth or vacuum cleaner nozzle.
5. Blow air into primary air holes on injector
holder.
6. In case any large clumps of dust have now
been pushed into burner repeat steps 3
and 4.
and 4.
Clean pilot assembly also. A yellow tip on
the pilot flame indicates dust and dirt in pilot
assembly. There is a small pilot air inlet hole
about 2" from where pilot flame comes out
of pilot assembly (see Figure 36). With unit
off, lightly blow air through the air inlet hole.
You may blow through a drinking straw if
compressed air is not available.
the pilot flame indicates dust and dirt in pilot
assembly. There is a small pilot air inlet hole
about 2" from where pilot flame comes out
of pilot assembly (see Figure 36). With unit
off, lightly blow air through the air inlet hole.
You may blow through a drinking straw if
compressed air is not available.
CABINET
Air Passageways
Use a vacuum cleaner or pressurized air to
clean.
Use a vacuum cleaner or pressurized air to
clean.
Exterior
Use a soft cloth dampened with a mild soap
and water mixture. Wipe cabinet to remove
dust.
Use a soft cloth dampened with a mild soap
and water mixture. Wipe cabinet to remove
dust.
Figure 36 - Pilot Inlet Air Hole
(Propane/LP Shown)
Pilot Assembly
Pilot Air Inlet Hole
Figure 35 - Injector Holder On Outlet
Burner Tube
Burner Tube
Injector
Holder
Holder
Primary Air Inlet Holes
Ports/Slots
WARNING: Turn off fireplace
and let cool before cleaning.
CAUTION: You must keep
control areas, burner, and cir-
culating air passageways of
fireplace clean. Inspect these
areas of fireplace before each
use. Have fireplace inspected
yearly by a qualified service
person. Fireplace may need
more frequent cleaning due to
excessive lint from carpeting,
bedding material, pet hair, etc.
WARNING: Failure to keep
the primary air opening(s) of
the burner(s) clean may result in
sooting and property damage.
BURNER INjECTOR HOLDER AND
PILOT AIR INLET HOLE
PILOT AIR INLET HOLE
The primary air inlet holes allow proper
amounts of air to mix with gas. This provides a
clean burning flame. Keep these holes clear of
dust, dirt, lint, and pet hair. Clean these air inlet
holes prior to each heating season. Blocked air
holes will create soot. We recommend that you
clean the unit every 3 months during operation
and have heater inspected yearly by a qualified
service person.
We also recommend that you keep burner
tube and pilot assembly clean and free of dust
and dirt. To clean these parts we recommend
using compressed air no greater than 30 PSI.
Your local computer store, hardware store, or
home center may carry compressed air in a
can. If using compressed air in a can, please
follow the directions on the can. If you don’t
follow directions on the can, you could dam-
age the pilot assembly.
1. Shut off unit, including pilot. Allow unit to
amounts of air to mix with gas. This provides a
clean burning flame. Keep these holes clear of
dust, dirt, lint, and pet hair. Clean these air inlet
holes prior to each heating season. Blocked air
holes will create soot. We recommend that you
clean the unit every 3 months during operation
and have heater inspected yearly by a qualified
service person.
We also recommend that you keep burner
tube and pilot assembly clean and free of dust
and dirt. To clean these parts we recommend
using compressed air no greater than 30 PSI.
Your local computer store, hardware store, or
home center may carry compressed air in a
can. If using compressed air in a can, please
follow the directions on the can. If you don’t
follow directions on the can, you could dam-
age the pilot assembly.
1. Shut off unit, including pilot. Allow unit to
cool for at least thirty minutes.
2. Inspect burner, pilot, and primary air inlet
holes on injector holder for dust and dirt
(see Figure 35).
(see Figure 35).
3. Blow air through ports/slots and holes in
burner.