Kenwood dnx890hd ユーザーズマニュアル
106
106
107
Operation
Controlling EQ curves
1
Select EQ curve from [Natural], [Rock],
[Pops], [Easy], [Top40], [Jazz], and
[User] using [
[Pops], [Easy], [Top40], [Jazz], and
[User] using [
2] and [3].
Controlling SystemQ-Ex
Selects items to be adjusted for tone curve
setup. If you turn off this setting, only Level
can be set up for tone curves.
setup. If you turn off this setting, only Level
can be set up for tone curves.
1
Touch [ON] or [OFF] of [SystemQ-Ex].
Controlling equalizer manually
1
Touch [Tone] in the Equalizer screen.
2
Set each item as follows.
FREQ
Adjusts the center frequency for each range.
Setting values are as follows.
Bass:
Adjusts the center frequency for each range.
Setting values are as follows.
Bass:
60Hz/70Hz/80Hz/100Hz/110Hz/120Hz/
130Hz/150Hz (Default is “100Hz”.)
130Hz/150Hz (Default is “100Hz”.)
Middle: 500Hz/1kHz/1.5kHz/2kHz (Default is
“1kHz”.)
Treble: 10kHz/12.5kHz/15kHz/17.5kHz (Default
is “12.5kHz”.)
LEVEL
Adjusts the level of each range.
Each setting value is within -8dB and 8dB and
default is “0dB”.
Q Factor
Adjust Q value for bass and middle.
Setting values are as follows.
Bass: 1.00/1.25/1.50/2.00 (Default is “1.00”.)
Middle: 1.00/2.00 (Default is “1.00”.)
Bass DC EXT
Turns Bass DC EXT on or off. Default is “OFF”.
If you select “ON”, the bass center frequency is
extended to the low register by approximately
20%.
[Flat]
Tone level becomes 0 (flat).
Subwoofer Level
Adjusts the subwoofer volume. This setting is
not available when subwoofer is set to “OFF”.
See
Adjusts the level of each range.
Each setting value is within -8dB and 8dB and
default is “0dB”.
Q Factor
Adjust Q value for bass and middle.
Setting values are as follows.
Bass: 1.00/1.25/1.50/2.00 (Default is “1.00”.)
Middle: 1.00/2.00 (Default is “1.00”.)
Bass DC EXT
Turns Bass DC EXT on or off. Default is “OFF”.
If you select “ON”, the bass center frequency is
extended to the low register by approximately
20%.
[Flat]
Tone level becomes 0 (flat).
Subwoofer Level
Adjusts the subwoofer volume. This setting is
not available when subwoofer is set to “OFF”.
See
.
Zone Control
You can select different sources for both
front and rear positions in the vehicle.
front and rear positions in the vehicle.
1
Touch [Zone Control].
Zone Control screen appears.
2
Touch [Dual Zone].
3
Set each source as follows.
[
3] (Front Source, Rear Source)
Select the audio source for each.
[
[
∞], [5] (Rear VOL.)
Adjusts the rear channel volume.
[Single Zone]
Touch to turn off the dual zone function.
[Single Zone]
Touch to turn off the dual zone function.
NOTE
• When the rear speaker sound is switched, the
audio source that is output at the AV OUTPUT
terminal is also switched to the same source.
terminal is also switched to the same source.
• When the dual zone function is set to on, the
following functions are not available.
• Output from the subwoofer
• Subwoofer Level/Bass Boost
• Output from the subwoofer
• Subwoofer Level/Bass Boost
• Equalizer Control/Space Enhancer
/Listening Position
• DSP Bypass Control
/Speaker
Setup/Car Type Setup