Desa flame-max vys18nb ユーザーズマニュアル
www.desatech.com
113093-01H
22
OPERATION
Continued
REMOTE READY MODELS
Figure 26 - Pilot
(Propane/LP)
Ignitor
Electrode
Electrode
Pilot
Burner
Burner
Figure 27 - Pilot
(Natural)
Pilot Burner
THERMOSTAT SERIES (MODEL
HRC200)
HRC200)
The hand-held remote can be operated
using either the manual mode (MANU) or
thermostatic mode (AUTO) (see Figure 30,
page 23). To select Fahrenheit/Centigrade
mode display, carefully press the ˚C/˚F mode
button with the end of a paper clip or similar
blunt object.
using either the manual mode (MANU) or
thermostatic mode (AUTO) (see Figure 30,
page 23). To select Fahrenheit/Centigrade
mode display, carefully press the ˚C/˚F mode
button with the end of a paper clip or similar
blunt object.
Manual Mode
1. Press the POWER and LOCK buttons
1. Press the POWER and LOCK buttons
together to turn on the hand-held remote
control.
control.
2. Press the MANU button to turn on the
fireplace.
3. Press the POWER and LOCK buttons
together to turn off the fireplace.
Figure 28 - Setting the Selector Switch,
Control Knob and Flame Adjustment
Knob for Hand-Held Remote Operation
ON
OFF
REMOTE
OFF
REMOTE
O
FF
P
ILOT
LO
IH
O
N
Selector Switch in Remote Position
(Optional Remote Control)
(Optional Remote Control)
Control Knob
in On Position
in On Position
Flame Adjustment Knob
Figure 29 - On/Off Hand-Held Remote
Control Unit (HRC100)
Control Button
Turns Burners
On and Off
Turns Burners
On and Off
Note: The burner may light if hand-held re-
mote was on when selector switch was last
turned off. You can now turn the burner on and
off with the hand-held remote control unit.
IMPORTANT: Do not leave the selector switch
in the REMOTE or ON position when the pilot
is not lit. This will drain the battery.
mote was on when selector switch was last
turned off. You can now turn the burner on and
off with the hand-held remote control unit.
IMPORTANT: Do not leave the selector switch
in the REMOTE or ON position when the pilot
is not lit. This will drain the battery.
ON/OFF SERIES (MODEL HRC100)
Hold the control button on the hand-held remote
until burner turns on. Hold the control button
again until burner turns off (see Figure 29).
TO LOCK press both buttons on hand-held
remote control until light stops flashing. Hand-
held remote control is now locked. If the fire
is on it will be turned off automatically. In the
locked state, the light will not light up when
any button is pressed.
TO UNLOCK press both buttons together
on hand-held remote control until the light
stops flashing. The hand-held remote is now
unlocked.
until burner turns on. Hold the control button
again until burner turns off (see Figure 29).
TO LOCK press both buttons on hand-held
remote control until light stops flashing. Hand-
held remote control is now locked. If the fire
is on it will be turned off automatically. In the
locked state, the light will not light up when
any button is pressed.
TO UNLOCK press both buttons together
on hand-held remote control until the light
stops flashing. The hand-held remote is now
unlocked.
MANUAL LIGHTING
PROCEDURE
1. Follow steps 1 through 6 under Lighting
Instructions, pages 20.
2. Depress control knob and light pilot
with match.
3. Keep control knob pressed in for 30 seconds
after lighting pilot. After 30 seconds, release
control knob. Now follow steps 9 through 11
under Lighting Instructions, page 20.
control knob. Now follow steps 9 through 11
under Lighting Instructions, page 20.
OPTIONAL HAND-HELD
REMOTE OPERATION
Note: All remote control accessories must
be purchased separately (see Accessories,
pages 31). Follow instructions included with
the remote control.
be purchased separately (see Accessories,
pages 31). Follow instructions included with
the remote control.
NOTICE: You must light the pilot
before using the hand-held re-
mote control unit. See Lighting
Instructions on page 20.
After lighting, let pilot flame burn for about one
minute. Turn control knob to ON position. Ad-
just flame adjustment knob anywhere between
HI and LO. Slide the selector switch to the
REMOTE position (see Figure 28).
minute. Turn control knob to ON position. Ad-
just flame adjustment knob anywhere between
HI and LO. Slide the selector switch to the
REMOTE position (see Figure 28).