Desa flame-max vys24pb ユーザーズマニュアル
www.desatech.com
113093-01H
17
Figure 20 - Installing Vintage Oak One-
Piece Log Set
One Piece
Log Set
Log Set
Chassis
Burner
“U”-shaped
Cutout in
Chassis
Cutout in
Chassis
INSTALLATION
Continued
PRESSURE TESTING HEATER GAS
CONNECTIONS
1. Open equipment shutoff valve (see
CONNECTIONS
1. Open equipment shutoff valve (see
Figure 17, page 16).
2. Open main gas valve located on or near
gas meter for natural gas or open pro-
pane/LP supply tank valve.
pane/LP supply tank valve.
3. Make sure control knob of heater is in the
OFF position.
4. Check all joints from equipment shutoff
valve to control valve (Manually-Controlled
Models) or to gas control (Remote-Ready
Models) (see Figures 18 and 19, page 16).
Apply noncorrosive leak detection fluid to
all joints. Bubbles forming show a leak.
Models) or to gas control (Remote-Ready
Models) (see Figures 18 and 19, page 16).
Apply noncorrosive leak detection fluid to
all joints. Bubbles forming show a leak.
5. Correct all leaks at once.
6. Light heater (see Operation, page 18 for
6. Light heater (see Operation, page 18 for
Manually-Controlled Models or page 20
for Remote-Ready Models). Check all
other internal joints for leaks.
for Remote-Ready Models). Check all
other internal joints for leaks.
7. Turn off heater (see To Turn Off Gas to
Appliance, page 19 for Manually-Con-
trolled Models or page 21 for Remote-
Ready Models).
trolled Models or page 21 for Remote-
Ready Models).
INSTALLING LOGS
WARNING: Failure to position
the parts in accordance with these
diagrams or failure to use only
parts specifically approved with
this heater may result in property
damage or personal injury.
CAUTION: After installa-
tion and periodically thereafter,
check to ensure that no flame
comes in contact with any log.
With the heater set to HI, check
to see if flames contact any log. If
so, reposition logs according to
the log installation instructions
in this manual. Flames contact-
ing logs will create soot.
It is very important to install the logs exactly
as instructed. Do not modify logs. Only use
logs supplied with heater.
as instructed. Do not modify logs. Only use
logs supplied with heater.
Vintage Oak Logs Only
1. Place one piece log set on grate to fit as
1. Place one piece log set on grate to fit as
illustrated in Figure 20. Make sure bottom
of front log is in front of “U”-shaped cutout in
center of chassis (see Figure 20). IMPOR-
TANT: Make sure log does not cover any
burner ports (see Figure 22, page 18).
of front log is in front of “U”-shaped cutout in
center of chassis (see Figure 20). IMPOR-
TANT: Make sure log does not cover any
burner ports (see Figure 22, page 18).
2. Place lava rock around base of heater if
desired.
Golden Oak Logs Only
1. Place back log #1 on grate to fit as il-
1. Place back log #1 on grate to fit as il-
lustrated in Figure 21. Make sure middle
section at bottom of log set is seated into
“U”-shaped cutout in center of chassis
(see Figure 21,). IMPORTANT: Make sure
log does not cover any burner ports (see
Figure 22, page 18).
section at bottom of log set is seated into
“U”-shaped cutout in center of chassis
(see Figure 21,). IMPORTANT: Make sure
log does not cover any burner ports (see
Figure 22, page 18).
Figure 21 - Installing Golden Oak Log Set
Chassis
Crossover
Log #3
Log #3
Burner
Front
Log #2
Log #2
Back
Log #1
Log #1
Grate
Prongs
Prongs