Whirlpool 1187617 ユーザーズマニュアル
5
It is the customer's responsibility:
■
To contact a qualified electrical installer.
■
To assure that the electrical installation is adequate and in
conformance with National Electrical Code, ANSI/NFPA 70 -
latest edition, and all local codes and ordinances.
conformance with National Electrical Code, ANSI/NFPA 70 -
latest edition, and all local codes and ordinances.
Copies of the standards listed may be obtained from:
National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
Batterymarch Park
Quincy, Massachusetts 02269
INSTALLATION
INSTRUCTIONS
Unpack the Air Conditioner
Remove packaging materials
■
Remove and properly dispose of packaging materials.
Remove tape and glue residue from surfaces before turning
on the air conditioner. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water
and dry.
Remove tape and glue residue from surfaces before turning
on the air conditioner. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water
and dry.
■
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your air conditioner.
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your air conditioner.
Metal or Wood Sliding Window Installation
■
Handle air conditioner with care. Watch out for sharp metal
fins on the rear coil.
fins on the rear coil.
■
Be sure your air conditioner does not fall out of the opening
during installation or removal.
during installation or removal.
■
The place where the power cord exits the air conditioner
should be no more than 4 ft (122 cm) from a grounded outlet.
should be no more than 4 ft (122 cm) from a grounded outlet.
■
Do not block the louvers on the front panel.
■
Do not block air movement on the outside of the air
conditioner.
conditioner.
■
The window frame assembly and side of structure must be
adequate to support weight of air conditioner.
adequate to support weight of air conditioner.
Install support platform
1. Slide open one window sash to install support platform.
2. Attach support platform to sill plate with three
³⁄₈ in. self-
tapping screws.
3. Loosely attach support angle to bottom of support platform
using two
⁷⁄₁₆ in. machine screws, flat washers and nuts.
4. Place support platform against lower window track and firmly
against vertical edge of window frame.
5. Attach support platform to windowsill using two 1 in. wood
screws.
If required, overcome interference of support platform with
window track or storm windows by securely attaching a shim
strip to the windowsill. Shim strip should be as long as width
of support platform and flush with back edge of sill.
Thickness of shim strip should be controlled by amount of
interference.
window track or storm windows by securely attaching a shim
strip to the windowsill. Shim strip should be as long as width
of support platform and flush with back edge of sill.
Thickness of shim strip should be controlled by amount of
interference.
Excessive Weight Hazard
Use two or more people to move and install
air conditioner.
air conditioner.
WARNING
Failure to do so can result in back or other injury.
1. Support plate
2.
2.
³⁄₈
in. self-tapping screws
3. Sill plate
1.
⁷⁄₁₆
in. machine screws
2. Support plate
3. Flat washer
4. Nut
3. Flat washer
4. Nut
5. Sill plate
6. Support angle
7. Leveling bolt and
6. Support angle
7. Leveling bolt and
locknut
1. 1 in. wood screws
2. Support plate
3. Lower window track
2. Support plate
3. Lower window track
4. Windowsill
5. Shim strip
5. Shim strip
1
2
3
2
3
4
4
1
5
6
7
1
2
3
4
5