Daewoo dv6t834b ユーザーズマニュアル

■ When you record a programs, the VCR places an index mark at the start of the recording. To search for an

index mark: 

Auto Play:

ON

Auto TV/VCR:

ON

Index Search
Go-To Search

If you want to search through a certain number
of index marks, press two number buttons to
enter the number of marks you want to search.
Press CLEAR on the remote to correct an entry.
or
Press REW to search backward or FF to search
forward. The VCR will locate your index mark
and begin playback. If you did not enter a
specific index number, the VCR will locate the
next index mark and begin playback. Press
STOP to stop index searching. 

Press REW or FF
to begin searching

or

Enter a specific
index number

- -

End:

SETUP

¥ If two
recordings

overlap, the index
mark for the second
program will be
erased. Therefore,
when you use the
index feature to find
the second program,
the VCR will skip
over it. 

¥ If you record

multiple programs in
one recording
session, the VCR will
only find the index
mark that was
placed on the video
cassette tape when
the recording
session began.

■ You can mark a segment of the video cassette with the tape counter that will help you easily locate the

segment later.  

Auto Play:

ON

Auto TV/VCR:

ON

Index Search

Go-To Search

The tape counter is displayed on the screen.
Input the tape counter you want to go and press
REW or FF, the VCR will search for the time
counter you want.

Current tape counter is

2 : 17 : 18

Press REW or FF
to go to - : - - : 00

Some index
marks  that may

be missed by the VCR :
¥ A mark too close to

your location on the
tape.

¥ The mark at the

beginning of a
recorded segment of
five minutes or less.

¥ The first index mark

on the tape when
you start at the
beginning of the
tape.

■ This feature allows the VCR to automatically start playing when you insert a tape with the safety tab

removed.

Move 

into ÒFUNCTIONSÓ with [ ] and

then, select the desired one with [ENTER]
button.

- Select ON if you want a tape with its safety

tab removed to start playing automatically
when the tape is inserted.

- Select OFF if you do not want a tape with

its safety tab removed to start playing
automatically. 

CLOCK SET
TIMER RECORDINGS
CHANNEL SET
FUNCTIONS
LANGUAGE SELECT

Auto Play:

ON

Auto TV/VCR:

ON

Index Search
Go-To Search

Move:

Select:

End:

SETUP

ENTER

Move:

Select:

End:

SETUP

ENTER

■ This feature controls whether the TV/VCR switch changes automatically to the VCR mode when the VCR is turned on.

Move 

into ÒFUNCTIONSÓ with [ ] and then, select the desired one with

[ENTER] button.

-  Select ON if you want the VCR to switch to

the VCR mode when the VCR is turned on
or a cassette is inserted. This only applies if
you connect the ANT.IN and RF OUT jacks
of your VCR and TV and watch  your VCR on
channel 3 of your TV.

-  Select OFF if you want the VCR to remain

in the TV mode. This is useful if you watch
your VCR on the TVÕs video input and you
donÕt want your antenna/cable signal
interrupted by the VCR. 

Auto Play:

ON

Auto TV/VCR:

ON

Index Search
Go-To Search

Move:

Select:

End:

SETUP

ENTER

Use PLAY, REW,or FF to reach the point on the tape that you would like to mark as
0:00:00.

Press [DISPLAY] button to display  the tape counter on the screen.

Press [CLEAR] button to reset the tape counter to 0:00:00.

You can continue to play the tape or perform other functions with the VCR.