Ingersoll-Rand aro pd15p-x ユーザーズマニュアル

2010

CCN 15197205

(800) 276-4658

FAX (800) 266-7016

INGERSOLL RAND COMPANY LTD

209 NORTH MAIN STREET -- BRYAN, OHIO 43506

1-1/2” DIAPHRAGM PUMP

OPERATOR’S MANUAL

PD15P-X

RELEASED:

9-5-03

REVISED:

5-12-10

(REV. 12)

INCLUDING: OPERATION, INSTALLATION & MAINTENANCE

1:1 RATIO (NON-METALLIC)

READ THIS MANUAL CAREFULLY BEFORE INSTALLING,

OPERATING OR SERVICING THIS EQUIPMENT.

It is the responsibility of the employer to place this information in the hands of the operator. Keep for future reference.

PE15P-X

SERVICE KITS

Refer to Model Description Chart to match the pump material options.
637389 for air section repair (see page 6).
637391-XX for fluid section repair (see page 4). NOTE: This kit also con-

tains several air motor seals which will need to be replaced.

637390-X major air valve assembly (see page 7).

PUMP DATA

Models

see Model Description Chart for “-XXX”.

. . . . . . . . . .

Pump Type

Non-Metallic Air Operated Double Diaphragm

. . . . . . .

Material

see Model Description Chart.

. . . . . . . . . .

Weight

PX15P-FKS-XXX

63.94 lbs (29.00 kgs)

. . .

. . . . . . .

PX15P-FPS-XXX

42.60 lbs (19.32 kgs)

. . . . . . .

PX15P-YKS-XXX

55.94 lbs (25.37 kgs)

. . . . . . .

PX15P-YPS-XXX

42.30 lbs (19.19 kgs)

. . . . . . .

Maximum Air Inlet Pressure

120 p.s.i.g. (8.3 bar)

. . . . . . . . .

Maximum Material Inlet Pressure

10 p.s.i.g. (0.69 bar)

. . . . .

Maximum Outlet Pressure

120 p.s.i.g. (8.3 bar)

. . . . . . . . . .

Maximum Flow Rate

(flooded inlet)

123.1 g.p.m. (465.9 l.p.m.)

. . . .

Displacement / Cycle @ 100 p.s.i.g.

0.617 gal. (2.34 lit.)

. . .

Maximum Particle Size

1/4” dia. (6.4 mm)

. . . . . . . . . . . .

Maximum Temperature Limits (diaphragm / ball / seal material)

E.P.R. / EPDM

-60

_ to 280_ F (-51_ to 138_ C)

. . . . . . . . . . .

Hytrel

-20

_ to 150_ F (-29_ to 66_ C)

. . . . . . . . . . . . . . . .

Nitrile

_ to 180_ F (-12_ to 82_ C)

. . . . . . . . . . . . . . . . .

Polypropylene

_ to 175_ F (2_ to 79_ C)

. . . . . . . . . . .

PVDF (Kynar

)

_ to 200_ F (-12_ to 93_ C)

. . . . . . . . . .

Santoprene

-40

_ to 225_ F (-40_ to 107_ C)

. . . . . . . . . . .

PTFE

_ to 225_ F (4_ to 107_ C)

. . . . . . . . . . . . . . . . .

Viton

-40

_ to 350_ F (-40_ to 177_ C)

. . . . . . . . . . . . . . . .

Dimensional Data

see page 8

. . . . . . . . . . . . . . . .

Mounting Dimension

8.687” x 14.937” (220.7 mm x 379.4 mm)

. . .

Noise Level @ 70 p.s.i., 60 c.p.m.

81.0 db(A)

{

. . . . .

The pump sound pressure levels published here have been updated to an Equivalent

Continuous Sound Level (L

Aeq

) to meet the intent of ANSI S1.13-1971, CAGI-PNEU-

ROP S5.1 using four microphone locations.

NOTICE: All possible options are shown in the chart, however, certain
combinations may not be recommended, consult a representative or the
factory if you have questions concerning availability.

PX15P-FXS-XXX

PX15P-YXS-XXX

MODEL DESCRIPTION CHART

P X 15 P - X X S - X X X

PX15P - XXS - X X X

637391 - X X

Diaphragm

Ball

FLUID SECTION SERVICE KIT SELECTION

EXAMPLE: Model # PD15P-FPS-PAA
Fluid Section Service Kit # 637391-AA

Seat Material
H - Hard 440 Stainless Steel
K - PVDF (Kynar)
P - Polypropylene
S - 316 Stainless Steel

Diaphragm Material
A - Santoprene

M - Medical Grade Santoprene

C - Hytrel

T - PTFE / Santoprene

G - Nitrile

V - Viton

Hardware Material
S - Stainless Steel

Fluid Caps & Manifold Material
K - PVDF (Kynar)
P - Polypropylene

Fluid Connection / Location
F - 1-1/2” A.N.S.I. / Din Flange / End
Y - 1-1/2” A.N.S.I. / Din Flange / Center

Center Section Material
P - Polypropylene

Ball Material
A - Santoprene

S - 316 Stainless Steel

C - Hytrel

T - PTFE

G - Nitrile

V - Viton

Electronic Interface
D - None
E - Available