ZyXEL Communications prestige 314 plus ユーザーズマニュアル
Prestige 314 PLUS Broadband Sharing Gateway with 4-Port Switch
5-10
Remote Node Setup
Table 5-5 Remote Node Network Layer Options Menu Fields
FIELD DESCRIPTION
EXAMPLE
IP Address
Assignment
Assignment
If your ISP did not assign you an explicit IP address, select Dynamic;
otherwise select Static and enter the IP address & subnet mask in the
following fields.
otherwise select Static and enter the IP address & subnet mask in the
following fields.
Dynamic
Rem IP Address If you have a Static IP Assignment, enter the IP address assigned to
the remote node.
192.168.1.1
Rem IP Subnet
Mask
Mask
If you have a Static IP Assignment, enter the subnet mask assigned
to the remote node.
to the remote node.
255.255.255.0
My WAN Addr
Some implementations, especially the UNIX derivatives, require the
WAN link to have a separate IP network number from the LAN and
each end must have a unique address within the WAN network
number. If this is the case, enter the IP address assigned to the WAN
port of your Prestige. Note that this is the address assigned to your
local Prestige, not the remote router.
WAN link to have a separate IP network number from the LAN and
each end must have a unique address within the WAN network
number. If this is the case, enter the IP address assigned to the WAN
port of your Prestige. Note that this is the address assigned to your
local Prestige, not the remote router.
Network
Address
Translation
Address
Translation
Use the [SPACE BAR] to select either Full Feature, None or SUA
Only. See the NAT chapter for a full discussion on this feature.
Only. See the NAT chapter for a full discussion on this feature.
SUA Only
Metric
The metric represents the “cost” of transmission for routing purposes.
IP routing uses hop count as the measurement of cost, with a
minimum of 1 for directly connected networks. Enter a number that
approximates the cost for this link. The number need not be precise,
but it must be between 1 and 15. In practice, 2 or 3 is usually a good
number.
IP routing uses hop count as the measurement of cost, with a
minimum of 1 for directly connected networks. Enter a number that
approximates the cost for this link. The number need not be precise,
but it must be between 1 and 15. In practice, 2 or 3 is usually a good
number.
1 to 15
Private
This parameter determines if the Prestige will include the route to this
remote node in its RIP broadcasts. If set to Yes, this route is kept
private and not included in RIP broadcast. If No, the route to this
remote node will be propagated to other hosts through RIP
broadcasts.
remote node in its RIP broadcasts. If set to Yes, this route is kept
private and not included in RIP broadcast. If No, the route to this
remote node will be propagated to other hosts through RIP
broadcasts.
Yes
RIP
Press the [SPACE BAR] to select the RIP direction. Options are
Both, None, In Only, Out Only or None.
Both, None, In Only, Out Only or None.
None
(default)
Version Press the [SPACE BAR] to select the RIP version. Options are RIP-1,
RIP-2B or RIP-2M.
RIP-1
Multicast
IGMP (Internet Group Multicast Protocol) is a session-layer protocol
used to establish membership in a Multicast group. The Prestige
supports both IGMP version 1 (IGMP-v1) and version 2 (IGMP-v2).
Press the [SPACE BAR] to enable IP Multicasting or select None to
disable it. See the previous Part for more information on this feature.
used to establish membership in a Multicast group. The Prestige
supports both IGMP version 1 (IGMP-v1) and version 2 (IGMP-v2).
Press the [SPACE BAR] to enable IP Multicasting or select None to
disable it. See the previous Part for more information on this feature.
None