Linear dxs-63-ec ユーザーズマニュアル
DXS-62/EC
DXS-63/EC
SUPERVISED
EMERGENCY
TRANSMITTERS
Operation Instructions
PRODUCT DESCRIPTION
The Models DXS-62 and DXS-63 are battery powered, miniature,
water-resistant*, supervised transmitters designed for use in emergency
applications with Linear’s DX and DXS Format receivers. Each is supplied
with a wristband, a pocket clip, and a Nylon pendant necklace. Pressing
buttons on either transmitter sends a digital coded wireless signal to its
companion receiver. To insure sending a complete signal,
press the transmitter button(s) for a minimum of two
seconds.
Each DXS transmitter is factory set to a unique code, so no fi eld coding
is required. The one-button DXS-62 sends a signal when its button is
pressed. The two-button DXS-63 transmitter sends a signal when both
buttons are pressed together. These transmitters can send a signal for
up to 30seconds per activation. The red signal indicator on the transmitter
lights and a built-in sounder beeps when the unit is activated.
If status transmissions are enabled, they will be sent every two hours.
Some receivers are able to use these signals, others are not.
Every two hours the transmitter tests for a low battery. This test takes
place even if status transmissions have not been enabled. If the battery
tests low, the transmitter sounder will beep and a low battery signal will
be sent.
Receivers must be programmed to the transmitter’s code before system
testing and operation. Refer to the receiver’s instructions for details on
operation and programming.
Each transmitter is sealed to provide water-resistance. The unit’s battery
is not replaceable. The transmitter should be discarded at the end of its
battery life.
water-resistant*, supervised transmitters designed for use in emergency
applications with Linear’s DX and DXS Format receivers. Each is supplied
with a wristband, a pocket clip, and a Nylon pendant necklace. Pressing
buttons on either transmitter sends a digital coded wireless signal to its
companion receiver. To insure sending a complete signal,
press the transmitter button(s) for a minimum of two
seconds.
Each DXS transmitter is factory set to a unique code, so no fi eld coding
is required. The one-button DXS-62 sends a signal when its button is
pressed. The two-button DXS-63 transmitter sends a signal when both
buttons are pressed together. These transmitters can send a signal for
up to 30seconds per activation. The red signal indicator on the transmitter
lights and a built-in sounder beeps when the unit is activated.
If status transmissions are enabled, they will be sent every two hours.
Some receivers are able to use these signals, others are not.
Every two hours the transmitter tests for a low battery. This test takes
place even if status transmissions have not been enabled. If the battery
tests low, the transmitter sounder will beep and a low battery signal will
be sent.
Receivers must be programmed to the transmitter’s code before system
testing and operation. Refer to the receiver’s instructions for details on
operation and programming.
Each transmitter is sealed to provide water-resistance. The unit’s battery
is not replaceable. The transmitter should be discarded at the end of its
battery life.
* NOTE: Water resistance not tested by UL
FEATURES
WRISTBAND INSTALLATION
PENDANT HOLDER INSTALLATION
POCKET CLIP INSTALLATION
STATUS OPTION & PROGRAMMING
SYSTEM TESTING
INTERNATIONAL WARRANTY
This Linear product is warranted against defects in material and workmanship for twelve (12)
months. The Warranty Expiration Date is labeled on the product. This warranty extends only
to wholesale customers who buy direct from Linear or through Linear’s normal distribution
channels. Linear does not warrant this product to consumers. Consumers should inquire
from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations
or liabilities on the part of Linear Corporation for consequential damages arising out
of or in connection with use or performance of this product or other indirect damages
with respect to loss of property, revenue, or profi t, or cost of removal, installation, or
reinstallation. All implied warranties, including implied warranties for merchantability and implied
warranties for fi tness, are valid only until Warranty Expiration Date as labeled on the product.
This Linear Corporation Warranty is in lieu of all other warranties express or implied.
For warranty service on Linear equipment return product, at sender’s expense to:
Linear Hong Kong 19/F Hounor Industrial Centre, 6 Sun Yip Street Chai Wan, Hong Kong
Attention: Repairs Department
months. The Warranty Expiration Date is labeled on the product. This warranty extends only
to wholesale customers who buy direct from Linear or through Linear’s normal distribution
channels. Linear does not warrant this product to consumers. Consumers should inquire
from their selling dealer as to the nature of the dealer’s warranty, if any. There are no obligations
or liabilities on the part of Linear Corporation for consequential damages arising out
of or in connection with use or performance of this product or other indirect damages
with respect to loss of property, revenue, or profi t, or cost of removal, installation, or
reinstallation. All implied warranties, including implied warranties for merchantability and implied
warranties for fi tness, are valid only until Warranty Expiration Date as labeled on the product.
This Linear Corporation Warranty is in lieu of all other warranties express or implied.
For warranty service on Linear equipment return product, at sender’s expense to:
Linear Hong Kong 19/F Hounor Industrial Centre, 6 Sun Yip Street Chai Wan, Hong Kong
Attention: Repairs Department
REPAIRS POLICY
Charges will be made for equipment that is not in warranty, shows customer abuse, or is
damaged by the effects of lightning, water, fi re, or other abnormal happenings.
Customer’s equipment sent in for repair may be repaired or replaced with new or remanufactured
equipment at Linear’s discretion.
The customer is always responsible for shipping and handling charges to the repairs facility.
Linear will pay return shipping and handling charges on “in warranty” products shipped back
to the customer. The customer will be billed for the return shipping and handling charges on “out
of warranty” products.
There will be a 50% expedite fee for any express requests.
The International Sales Manager must be notifi ed prior to the return of product to Linear. All
international returns must have an International Repair Authorization number (IRA#). The number
must be marked on all packages. Failure to do so will cause delays in processing.
IMPORTANT !!!
Linear radio controls provide a reliable communications link and fi ll an important need in portable
wireless signaling. However, there are some limitations which must be observed.
The radios are required to comply with local rules and regulations as radio devices. As such, they
have limited transmitter power and therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and may be blocked
by radio signals that occur on or near their operating frequencies, regardless of code settings.
Changes or modifi cations to the device may void regulatory compliance.
Infrequently used radio links should be tested regularly to protect against undetected interference
or
or
fault.
A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale
distributor or dealer, and these facts should be communicated to the ultimate users.
(760) 438-7000 • FAX (760) 438-7043
www.linearcorp.com
Copyright © 2003 Linear Corporation 215558 D
NOTE: NECKLACE SIDE OF PENDANT HOLDER
FITS CLOSEST TO THE SIGNAL INDICATOR
FITS CLOSEST TO THE SIGNAL INDICATOR
TO INSTALL PENDANT HOLDER, SLIDE HOLDER
INTO SLOTS ON ENDS OF TRANSMITTER
INTO SLOTS ON ENDS OF TRANSMITTER
INSTALL THE PENDANT HOLDER
THEN CUT AND REMOVE THE NECKLACE
THEN CUT AND REMOVE THE NECKLACE
SNAP THE POCKET CLIP
INTO THE PENDANT HOLDER
INTO THE PENDANT HOLDER
BEEP... BEEP...
BEEP... BEEP...
BEEP
IF THE FOUR HOUR STATUS TIMER IS REQUIRED FOR
SUPERVISION, PERMANENTLY ENABLE THE TIMER BY
PRESSING THE TRANSMITTER BUTTON FIVE TIMES IN
SUCCESSION (USE THE LEFT BUTTON ON DXS-63). THE DXS-62
WILL BEEP AFTER EACH BUTTON PRESS, THE DXS-63 WILL
NOT. FIVE BEEPS WILL SOUND WHEN THE TIMER IS ENABLED.
SUPERVISION, PERMANENTLY ENABLE THE TIMER BY
PRESSING THE TRANSMITTER BUTTON FIVE TIMES IN
SUCCESSION (USE THE LEFT BUTTON ON DXS-63). THE DXS-62
WILL BEEP AFTER EACH BUTTON PRESS, THE DXS-63 WILL
NOT. FIVE BEEPS WILL SOUND WHEN THE TIMER IS ENABLED.
PROGRAM THE TRANSMITTER INTO THE RECEIVER BY
PLACING THE RECEIVER INTO PROGRAM MODE, THEN SEND
A SIGNAL TO THE RECEIVER FROM THE TRANSMITTER.
REFER TO THE RECEIVER'S PROGRAMMING INSTRUCTIONS
FOR DETAILS.
PLACING THE RECEIVER INTO PROGRAM MODE, THEN SEND
A SIGNAL TO THE RECEIVER FROM THE TRANSMITTER.
REFER TO THE RECEIVER'S PROGRAMMING INSTRUCTIONS
FOR DETAILS.
NOTE: THE END OF STRAP WITH VELCRO ATTACHES
TO THE END CLOSEST TO THE SIGNAL INDICATOR
TO THE END CLOSEST TO THE SIGNAL INDICATOR
TO INSTALL WRISTBAND, SLIDE STRAPS
INTO SLOTS ON ENDS OF TRANSMITTER
INTO SLOTS ON ENDS OF TRANSMITTER
BEEP...
IMPORTANT! TEST SYSTEM WEEKLY
The manufacturer strongly recommends that you test
security equipment frequently. Over a period of time, no
electronic products are better than the inspection and
maintenence they receive. Therefore, from the time of
installation, it is absolutely necessary to test the system
at least once a week.
security equipment frequently. Over a period of time, no
electronic products are better than the inspection and
maintenence they receive. Therefore, from the time of
installation, it is absolutely necessary to test the system
at least once a week.
PLACE THE RECEIVER IN A "TEST"
MODE AND ACTIVATE THE
TRANSMITTTER. VERIFY THAT THE
SIGNAL IS RECEIVED AND THAT THE
SYSTEM REPORTS AS REQUIRED.
MODE AND ACTIVATE THE
TRANSMITTTER. VERIFY THAT THE
SIGNAL IS RECEIVED AND THAT THE
SYSTEM REPORTS AS REQUIRED.
DXS-62
DXS-63
ACTIVATION
BUTTON
SIGNAL
INDICATOR
ACTIVATION
BUTTONS
(PRESS BOTH)
PENDANT HOLDER
NYLON
NECKLACE
POCKET
CLIP
WRIST
STRAP
PRINTER’S INSTRUCTIONS:
INSTR,INST,DXS-62,63/EC - LINEAR P/N: 215558 D - INK: BLACK - MATERIAL: 20 LB. MEAD BOND - SIZE: 8.500” X 11.000” - SCALE: 1-1
BY