Morphy Richards ib4070x ユーザーズマニュアル

4

Components of your
iron

⁄ Variable steam button
¤ Shot of steam button
‹ Spray button
› Filling hole with cap
fi Spray nozzle
fl Soleplate
‡ Temperature control dial with indicator
· Water tank
‚ Life long anti-scale (certain models only)
„ Temperature indicator light (red)
‰ Filling beaker
 Auto shut-off indicator 

(certain models only)

Before use

Note: The steam facility should only be

used on garments which are suitable for
ironing at the 2 and 3 dot settings.

When ironing with the steam facility at the

2 dot setting, the steam output should be set
at the lower end of the steam range (see
variable steam section).

Textiles and clothes are supposed to

carry ironing instructions. If they don’t you
should follow the fabric guide on page 3, but
be sure to test the temperature by ironing the
hem of the garment or similar area first.

If you turn the control dial down from a

hot setting to a cooler setting, wait until the
iron temperature has stabilised before you
continue ironing.

Filling

1 Make sure that the iron is not plugged in

and then set the variable steam control 

⁄

to the ‘0’ position before filling the iron
with water.

2 Lift up the fill cap and fill the water

through the filling hole 

› into the water

tank 

·, using the beaker provided. A

After filling replace the fill cap. In hard
water areas the use of distilled or
demineralised water is recommended.
WARNING: Never use battery topping

up fluid or water containing any
substances like starch, or sugar, or
defrosted water from a refridgerator.
3 Always pour out the remaining water after

use.
WARNING: When filling your iron with

Temperature control

Plug in the iron and switch on. Set the

temperature control dial 

B to the

temperature required, but don’t start ironing
immediately. 

⁄

¤ ‹

›

fi

fl

‡

·

‚

„

‰

B

A

Â

If you wait a few minutes, the iron will

stabilise at the required setting. Your
Morphy Richards iron is fitted with an
indicator light 

„ which will go on and off

while you are ironing. 

This is perfectly normal as it shows that

the iron is maintaining the heat setting you
have chosen.

It is always a good idea to begin with

cool fabrics and work up to higher settings.

An iron heats up quicker than it cools

down so you’ll save time and electricity.

Features of your iron

The indicator light shows that the iron is

warming up. When the required temperature
is reached the light will go out and will cycle
on-off during operation.

You can use your iron as a dry iron only.

Make sure the variable steam control 

⁄ is

set to the ‘0’ symbol.

Any temperature setting may be used

depending on the garment. The spray
feature may be used provided there is water
in the tank (see filling section). You do not
need to put any water in the tank when dry
ironing only.

Press the spray button 

‹ and aim the

spray of water at stubborn creases. You can
do this whilst dry ironing
providing there is water in the
tank. When using the water
spray it may be necessary to
push the button a few times to
get the spray pump primed.

Fill the iron with water as described in

‘Filling’, page 4 and insert the plug into the
electrical socket.

The steam output can be varied from

low to high by turning the variable steam
control 

C. When using the iron at the

bottom of the steam range, the steam
output should be adjusted to the low
setting.

The steam facility should only be used

on garments which are suitable for ironing
at 2 and 3 dot setting.

Press the shot of steam button 

¤ to

obtain a burst of extra steam for ironing out
creases in heavy material such as denim
etc.

The shot of steam can be used whilst

dry ironing, providing there is water in the
tank, and the temperature control is set
within the steam range.

Do not use shot of steam

at temperatures below the
steam range shown on the
control dial.

Note: For optimum steam

quality, do not operate the
shot more than three times in
succession.

5

Steam off

C

‘MAX’ steam

Job: 40700 Rev 1 -- Color: Composite -- Signature 2, Sheet 1, Back -- Plate 4