opcode studio 4 ユーザーズマニュアル
PART 1: Overview and Installation
8
Opcode Systems, Inc.
NOTE:
The Studio 4 driver software must
match the speed selected by the 1MHz/Fast
switch. Configure the Studio 4 driver soft-
ware as discussed in the “Studio 4<-
>Macintosh Communication Speed” sec-
tion in Chapter 5.
switch. Configure the Studio 4 driver soft-
ware as discussed in the “Studio 4<-
>Macintosh Communication Speed” sec-
tion in Chapter 5.
1-8/9-16 Switch
Select the 1-8 position (switch in) if the
Studio 4 is the first or only Studio 4 in a
network. This assigns port numbers 1
through 8 to the Studio 4's eight MIDI
ports.
Studio 4 is the first or only Studio 4 in a
network. This assigns port numbers 1
through 8 to the Studio 4's eight MIDI
ports.
Select the 9-16 position (switch out) if the
Studio 4 is the second in a network. This
assigns port numbers 9 through 16 to the
Studio 4's eight MIDI ports. Network con-
nections are discussed in Chapter 3.
Studio 4 is the second in a network. This
assigns port numbers 9 through 16 to the
Studio 4's eight MIDI ports. Network con-
nections are discussed in Chapter 3.
NOTE:
If you are using just one Studio 4,
set this switch to the 1-8 position.
Thru Switches (A & B)
These switches provide convenient
access to printers, modems or other
peripherals.
access to printers, modems or other
peripherals.
When a Thru switch is in the MIDI posi-
tion, the Studio 4 is in MIDI mode—
transmitting MIDI data between your
Macintosh and various studio devices.
tion, the Studio 4 is in MIDI mode—
transmitting MIDI data between your
Macintosh and various studio devices.
When a Thru switch is in the THRU posi-
tion, data from the Macintosh (as
received on either the “A” or “B” input
ports) is passed through the Studio 4 to
the “A Thru” or “B Thru” ports on the rear
panel. Set a Thru switch to the THRU
tion, data from the Macintosh (as
received on either the “A” or “B” input
ports) is passed through the Studio 4 to
the “A Thru” or “B Thru” ports on the rear
panel. Set a Thru switch to the THRU
position when your Macintosh needs to
communicate with an external peripheral
(such as a printer or modem).
communicate with an external peripheral
(such as a printer or modem).
SMPTE/Power Indicator Light
This LED blinks when there is any
SMPTE activity. When no timecode is
sent or received, the LED is lit as a power
indicator.
SMPTE activity. When no timecode is
sent or received, the LED is lit as a power
indicator.
Power Switch
When pushed in, the power is ON. When
out, the power is OFF. The SMPTE/
Power LED should light when the switch
is in the ON position if the power supply is
connected to the Studio 4 and plugged in.
out, the power is OFF. The SMPTE/
Power LED should light when the switch
is in the ON position if the power supply is
connected to the Studio 4 and plugged in.
THE STUDIO 4 REAR PANEL
Figure 2.2: Studio 4 Rear Panel
From left to right, the rear panel connec-
tors are as follows:
tors are as follows:
Power Connector
Plug the power supply into this jack. Use
only a 9VDC 1.5A center-positive power
supply. The power supply is included with
the Studio 4.
only a 9VDC 1.5A center-positive power
supply. The power supply is included with
the Studio 4.
OUT
MIDI OUT
MIDI IN
SMPTE
IN
PORT B
PORT A
B
THRU
A
THRU
9VDC
8
16
7
15
6
14
5
13
4
12
3
11
2
10
1
9
6
14
5
13
4
12
3
11
2
10
1
9