giant-bicycles continuum ユーザーズマニュアル

1. 2.

3. 4.

A. PHYSICAL DESCRIPTIONS

B. INSTALLATION

C. BATTERY REPLACEMENT

SENSOR and MAGNET MOUNTING

MOUNTING BRACKET INSTALLATION (Fig. E)

SECURING THE SENSOR CABLE (Fig. G)

INSTALLING THE MAIN UNIT (Fig. F)

PRECAUTIONS

1. Mount the SENSOR with 2 cable ties on the front fork with the

RUBBER PAD , and let the sensor face the spoke, do not tighten the

cable ties before the sensor is placed in the right position. (Fig. A)

2. Mount the MAGNET on one spoke of the front wheel and let the magnet

face the sensing zones . Place the RING around the nut to enhance

the reliability of the fixed screw. (Fig. B)

(New magnet with cross gap fit to all wheel spokes both aero and round).

3. Adjust the relative position between the sensor and the magnet. (Fig. C)

a. Align the center of the MAGNET to either of the sensing zones .

b. Make sure the GAP between the magnet and the sensor is within

4mm (1/6 inch). Adjust the desired gap by moving both the magnet

and the sensor up or down.

IMPORTANT: If either a) or b) is incorrect, poor signal input will result.

4. Be sure all relative positions are correct, tightening the cable ties so they

will not move.

5. Cut the excess strapping on the cable ties when the installation is finished.

(Fig. D)

1. Two rubber shims are included to attach the mounting bracket to your

handlebar securely. The thinner shim is to be used with large diameter

handlebars up to 31.8 mm . The thicker shim is to be used with 25.4 mm

or greater diameter bars. Both shims can be used for bars less than

25.4 mm .

2. To secure the bracket to the handlebar, place the mounting bracket in the

correct position, run cable ties through the passages in the bracket, wrap

around the bar and fit pad(s), insert into the cable tie closure, and pull tight.

Do not tighten cable ties before the bracket is in the proper position.

3. CAUTION! When trimming the cable ties, be sure not to leave any sharp

rough ends which could result in injury.

1. Select suitable positions to secure the sensor cable to the fork with CABLE

TIES.

2. Make sure the sensor cable is loose enough for the handlebar to turn

freely before tightening the cable ties.

3. Secure excess wire near the fork crown by wrapping it around the front

brake cable or by bending it back and forth and securing it with cable ties.

1. Mount the main unit onto the bracket by sliding it from front to rear until it

clicks into position.

2. This bracket is designed with a locking lever to secure the main unit and

prevent it from coming loose during use.

3. To remove the main unit, press down on the lock lever, then pull the main

unit forward and off.

1. When the brightness of the LCD display begins to dim, this

indicates that the battery is nearly exhausted.

2. Replace with a new LR44 (Cross reference type A76, AG13 or

V13GA) battery in the compartment on the back of the computer

with the positive (+) pole toward the battery cap. (Fig. H)

1. This computer can be used in the rain but should not be used under water.

2. Don't leave the main unit exposed to direct sunlight when not riding the

bike.

3. Don't disassemble the main unit or it's accessories.

4. Check relative position and gap of sensor and magnet periodically.

5. Clean the contacts of the bracket and the bottom of the main unit

periodically.

6. Don't use thinner, alcohol or benzine to clean the main unit or its

accessories when they become dirty.

7. Remember to pay attention to the road while riding.

Check the following before taking unit in for repairs.

English

1. LCD DISLPAY

2. MODE BUTTON

3. BATTERY CAP

4. ALL CLEAR (AC) KEY

5. CONTACTS

6. RING

7. MAGNET

8. BRACKET

9. 1.5V BATTERY

(LR44 IS TYPICAL)

10. BRACKET RUBBER PAD x 3

11. SENSOR RUBBER PAD

12. SENSOR

13. SENSING ZONES

14. CABLE TIES (S x 5)

15. CABLE TIES (L x 4)

TROUBLE SHOOTING

PROBLEM

1.Is the battery dead?
2.Is there incorrect battery installation?

1.Replace the battery.
2.Be sure that the positive pole of the
   battery is facing the battery cap.
1.Refer to the adjusting procedure and
   complete the adjustment.
2. Wipe contacts clean.
3. Refer to (Fig.B) and (Fig.C) and
    readjust data correctly.
4.Repair or replace wire.
5.Refer to "CALIBRATION" and enter
   correct value.
Refer to the "MAIN UNIT SETUP" and
initiate the computer again.
Place main unit in the shade to return
to normal state.No adverse effect on
data.
Unit will return to normal state when
the temperature rises.

1. Is it at the recalibrating or 12HR
    clock setting screen?
2. Are the contacts between the main
    unit and the bracket poor?
3.Are the relative positions and gap of
    sensor and magnet correct?
4.Is the wire broken?
5.Is the circumference correct?

Was the main unit under direct
sunlight when not riding the bike for a
long time?
Is the temperature below 0 C (32 F)?

Main Unit:
No display

No current
Speed or
incorrect
data

Irregular
display
LCD is
black

Display is
slow

CHECK ITEMS

REMEDY

OK!

FORK

Battery Cap

COIN

Spoke

SENSING ZONES

Magnet center aligns to the

Gap < 4mm (1/6inch)

For Round

Spoke

For Flat

Spoke

Fig. D

Fig. E

Fig. F

Fig. G

Fig. H

Fig. C

Fig. B

Fig. A

Press down on this lock lever
before removing the main unit.

Slide On

Lever

BRACKET

CONTINUUM 5/8

CYCLE COMPUTER

2
3