Panasonic DMREZ27EB 操作ガイド
70
RQT8856
Messages
On the Unit’s Display
Page
H , F
(“ ” stands for a service number.)
(“ ” stands for a service number.)
An error has occurred. The number following “H” or “F” depends on the
status of the unit. Check the items below and in the Troubleshooting Guide.
If the service number still does not disappear after the check, reset the unit
(
➔ 61, “To restore the unit if it freezes” ).
•
−
If the service numbers fail to clear, note the service numbers and contact a
qualified service person.
•
−
DVD
(“ ” stands for a number.)
(“ ” stands for a number.)
The remote control and the main unit are using different codes. Change the
code on the remote control.
•
61
HARD ERR*
If there is no change after turning the unit on and off, consult the dealer where
the unit was purchased.
•
−
NoREAD*
The disc is dirty or badly scratched. The unit cannot record, play, or edit.
•
58
The disc may be incompatible or of poor quality.
•
59
You have used a lens cleaner and it has finished operation. Press [; OPEN/
CLOSE] on the main unit to eject the disc.
•
5
FINAL
When the screen asking if you want to finalise the disc appears, the message
is displayed.
•
19
PLEASE WAIT*
Displayed when the unit is started. This is not a malfunction.
•
−
The unit is carrying out its recovery process. You cannot operate the unit while
the message is displayed.
•
−
PROG FULL*
There are already 16 timer recording programmes. Delete unnecessary timer-
recording programmes.
•
25
SW-DL
The unit is performing a software update.
•
52
UNSUPPORT*
You have inserted a disc the unit cannot play or record onto.
•
59
UNFORMAT*
You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL or
DVD-RW (DVD-Video format) that has been recorded on other equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted.
•
19, 44
F74
The HDMI connection could not be authenticated due to a transfer malfunction.
Consult the dealer where the unit was purchased.
•
−
F75
The HDMI connection could not be authenticated due to an internal data
malfunction.
Consult the dealer where the unit was purchased.
•
−
U59
The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until the
message disappears.
Select a position with good ventilation when installing the unit. Do not block the cooling
fan on the rear of the unit.
•
−
U61
(When a disc is not inserted) Displays when a malfunction has occurred
during recording, playback or copy. This is displayed when the unit is in the
recovery process to return to normal operation; it is not broken. Once the
display disappears you can use the unit again.
•
−
U72
U73
U73
The HDMI connection acts unusually.
The connected equipment is not HDMI compatible.
The HDMI cable is too long. Please use a cable 5.0 meters or less.
The HDMI cable is damaged.
•
–
–
–
−
U76
HDMI cannot be output because you are connected to a model that does not
support copyright protection.
•
−
U88
There was something unusual detected with the disc while recording, playing;
there was a power failure or the AC mains lead was disconnected while the unit
was on. The unit is carrying out its recovery process. This process restores the unit
to normal operation. The unit is not broken. Wait until the message disappears.
•
63
U81
U82
U99
U82
U99
The unit fails to operate properly. Press [^/I] on the main unit to switch the unit
to standby mode. Press [^/I] on the main unit again to turn the unit on.
•
−
X HOLD
The Child Lock function is activated.
Press and hold [OK] and [RETURN] simultaneously until “X HOLD”
disappears.
•
53
* The message are alternately displayed.
RQT8856-B_DTP_070306.indb 70
RQT8856-B_DTP_070306.indb 70
2007/04/04 17:49:49
2007/04/04 17:49:49