Panasonic DMREX88 操作ガイド
28
RQT9078
[HDD] [RAM] [-R] [-RW‹V›] [+R] [+RW]
Manual Recording
Preparation:
]RAM\ If the disc is protected, release protection
]RAM\ If the disc is protected, release protection
(
68).
Connect a satellite receiver to this unit’s input
terminals (
11).
When the output signal from the external equipment
is NTSC, change the “TV System” to “NTSC” in the
Setup menu (
Setup menu (
75).
With the unit stopped.
SELECT
INPUT
to select “AV2” for the
satellite receiver you have
connected.
Select the channel on the satellite
receiver.
REC MODE
to select the recording
mode.
Tips
To skip unwanted parts
Press [
Press [
PAUSE] to pause recording. (Press again to restart
recording.)
To stop recording
Press [
Press [
STOP].
Linked timer recordings with external
equipment (SKY Digital STB/satellite
receiver) — EXT LINK
equipment (SKY Digital STB/satellite
receiver) — EXT LINK
Preparation:
]RAM\ If the disc is protected, release protection
]RAM\ If the disc is protected, release protection
(
68).
Make sure you connect the AV2 terminal of this unit
to “VCR Scart Terminal” of a SKY Digital STB/
satellite receiver with a 21-pin scart cable (
satellite receiver with a 21-pin scart cable (
11).
Set the “AV2 Input” and “Ext Link” to match the
connected equipment in the Setup menu (
75).
Make timer programming on SKY
Digital STB/satellite receiver.
− Refer to the equipment’s operating instructions.
DRIVE
SELECT
SELECT
to select the HDD or DVD
drive.
− If you selected the DVD drive, insert a disc
(
81).
Tips
To cancel the external control
Press [EXT LINK] to stop recording or to cancel linked timer
recording standby (The unit turns on and ‘‘EXT-L” disappears.).
Press [EXT LINK] to stop recording or to cancel linked timer
recording standby (The unit turns on and ‘‘EXT-L” disappears.).
Manual timer recordings (
30)
Notes
In order to prevent accidental operation, press [EXT LINK] to
cancel the setting after recording is fi nished.
This function does not work when “TV system” is set to “NTSC” in
the setup menu (
75).
This function does not work with some equipment. Refer to the
equipment’s operating instructions.
The beginnings of recordings may not be recorded correctly in
some cases.
Programmes are recorded as one title on this unit when the end
time of the earlier timer recording and the start time of the later
timer recording are close to each other.
[HDD] [RAM] To divide the titles, go to “Divide Title” ( 49).
timer recording are close to each other.
[HDD] [RAM] To divide the titles, go to “Divide Title” ( 49).
While the unit is in EXT LINK standby mode or recording, video
picture is from the AV2 terminal irrespective of “AV1 Output”
setting (
setting (
75).
REC
to start recording.
To record programmes from a SKY Digital STB/satellite
receiver using timer programming
receiver using timer programming
EXT LINK
− The unit turns off and “EXT-L” lights on the
unit’s display to indicate timer recording
standby has been activated.
standby has been activated.
− While the unit is in EXT LINK standby mode
or recording, most operations on this unit are
prohibited ([
prohibited ([
OPEN/CLOSE], [/l] etc.).
When you operate, press [EXT LINK] to
cancel EXT LINK standby mode or recording
cancel EXT LINK standby mode or recording
(The unit turns on and “EXT-L” disappears.).
Recording from a Satellite Receiver
DRIVE
SELECT
SELECT
to select the HDD or DVD
drive.
− If you selected the DVD drive, insert a disc
(
81).
This unit cannot record NTSC signals to discs that
already have PAL signal recordings. (However, both
types of programmes can be recorded onto the HDD.)
types of programmes can be recorded onto the HDD.)
DMR-EX78_88EB.indb 28
DMR-EX78_88EB.indb 28
2008/02/14 12:17:50
2008/02/14 12:17:50