Aten KH2516A DCP2945 クイック設定ガイド

1

2

3

4

5-1

5-2

1 KH2508

A

 or KH2516

A

 Cat 5 High-Density KVM Switch

1 Firmware Upgrade Cable

1 Power Cord

1 Rack Mount Kit

1 Foot Pad Set (4 pcs.)

1 User Instructions

1. Port Selection Buttons

2. Port LEDs

3. Reset Switch

4. Console Selection Buttons

5. Firmware Upgrade Recovery Switch

6. Firmware Upgrade Port

7. Power LED

8. Station ID LED

1. Power Socket

2. Power Switch

3. Daisy Chain Ports

4. Grounding Terminal

5. Console 1 Ports

6. Console 2 Ports

7. KVM Port Section

• A VGA, SVGA, or multisync monitor capable of the highest resolution that you will be using on any computer in 

the installation

• A PS/2 or USB mouse

• A PS/2 or USB keyboard

The following equipment must be installed on the computers that connect to the KH2508

A

 or KH2516

A

 KVM 

ports:

• A VGA, SVGA or multisync port

• A Type A USB port and USB host controller (for USB KVM adapter cable connection)

- or -

6-pin Mini-DIN keyboard and mouse ports (for PS/2 KVM adapter cable connection)

• Cat 5e/6 cable is required to connect the KH2508

A

 / KH2516

A

 to one of the KVM adapter cables.

• The following KVM adapter cables are required for use with the KH2508

A

/ KH2516

A

:

In a single stage installation, there are no additional KVM switches daisy chained down from the KH2508

A

 / 

KH2516

A

. To set up a single stage installation, refer to the installation diagrams starting (the numbers in the 

diagram correspond with the numbers of the instruction steps), and do the following:

1. Ground the KH2508

A

 / KH2516

A

 by connecting one end of the grounding wire provided with your switch to the 

grounding terminal, and the other end of the wire to a suitable grounded object.

Note: Do not omit this step. Proper grounding helps to prevent damage to the unit from surges or static 

electricity.

2. Plug the console keyboards, monitors, and mice into the unit’s Console 1 and Console 2 console ports. The ports 

are color coded and marked with icons for easy identification.

Note: You can use any combination of keyboard and mouse connections. For example, you can use a PS/2 

keyboard with a USB mouse.

3. Use Cat 5e/6 cable to connect any available KVM port to a KVM adapter cable that is appropriate for the 

computer you are installing.

Note: The KH2508

A

 / KH2516

A

 does not support distances greater than 50 m between itself and the KVM 

adapter cable.

4. Connect the KVM adapter cable to the computer.

Plug the connectors on the KVM adapter cable into the appropriate ports of the computer you are installing.

5. Plug the female end of the power cord into the KH2508

A

 / KH2516

A

's power socket; plug the male end into an 

AC power source.

 After the KH2508

A

 / KH2516

A

 is cabled up, you can turn on the power. After it is powered up, you can turn on the 

servers.

The KH2508

A

 / KH2516

A

 can be mounted in a 19" (1U) rack. The mounting brackets can screw into either the front 

or the back of the unit so that it can attach to the front or the back of the rack. To rack mount the unit:

1. Remove the screws at the front or the rear, as shown in the diagram below.

2. Screw the mounting brackets into the sides of the unit at the front or the rear, as shown in the diagram below.

3. Slide the unit into the front or rear of the rack and secure it to the rack.

Connect to devices with PS/2 ports  

KA7920 / KA7520 / KA7120 / KA9520 / KA9120

Connect to devices with USB ports  

KA7970 / KA7570 / KA7170 / KA9570/ KA9170

Connect to Sun Legacy systems (with 13W3 port)  

KA9130 / KA7130 

Connect to Sun USB systems  

KA9170 / KA7170 

Connect to serial based devices  

KA9140 

Note: The front and rear panel views are similar for the KH2508

A

, the difference being that the 

KH2508

A

 has only one row of LED lights (front) and one row of CPU ports (rear)

Phillips head hex

M3 x 8

Phillips head hex

M3 x 6

Phillips head hex

M3 x 6

© Copyright 2012 ATEN

®

 International Co., Ltd.   www.aten.com

Altusen and the Altusen logo are trademarks of ATEN International Co., Ltd. 
All rights reserved. All other trademarks are the property of their respective owners.
This product is RoHS compliant    

CN ZL 98252015.8
CN ZL 02122202.9
CN ZL 200410008850.2
CN ZL 200410031689.0
CN ZL 200410042771.3

DE 29903667.7
DE 102004017843
DE 102004019107
TW 194030
TW 183765

TW I276963
TW I237762
TW I269992
US 6160543
US 7386584

US 7640289
US 7415552
US 7613854
US 7584309
JP 3917598

JP 4456936
GB 2412456
FR 0500514 

All information, documentation, and specifications contained in this media are subject to change without prior notification by the manufacturer. 
Please visit our website to find the most up to date version. 

Online Registration
International:
• http://support.aten.com
North America:
• http://www.aten-usa.com/product_registration  

 
Technical Phone Support
International:
• 886-2-8692-6959
China:
• 86-10-5255-0110
Japan:
• 81-3-5615-5811
Korea:
• 82-2-467-6789
North America:
• 1-888-999-ATEN   Ext: 4988  
United Kingdom:
• 44-8-4481-58923