Panasonic KXTG8321FX 操作ガイド
Programming
35
Registering a handset to a
base unit
base unit
The supplied handset and base unit are
pre-registered. If for some reason the
handset is not registered to the base unit
(for example, w flashes even when the
handset is near the base unit), register
the handset.
pre-registered. If for some reason the
handset is not registered to the base unit
(for example, w flashes even when the
handset is near the base unit), register
the handset.
1
Handset:
K
K
(centre of joystick) i N i
M
2
{V}
/{^}: “Registration” i M
2 times
3
{V}
/{^}: Select a base unit number.
i
M
L
This number is used by the
handset as a reference only.
handset as a reference only.
4
Base unit:
Proceed with the operation for your
model.
■ KX-TG8301/KX-TG8302
Proceed with the operation for your
model.
■ KX-TG8301/KX-TG8302
Press and hold {x} for about 5
seconds. (No registration tone)
seconds. (No registration tone)
■ KX-TG8321
Press and hold {x} for about 5
seconds, until the registration
tone sounds.
seconds, until the registration
tone sounds.
L
If all registered handsets start
ringing, press the same button to
stop. Then repeat this step.
ringing, press the same button to
stop. Then repeat this step.
L
The next step should be
completed within 90 seconds.
completed within 90 seconds.
5
Handset:
Wait until “Enter Base PIN” is
displayed. i Enter the base unit
PIN (default: “0000”). i M
L
Wait until “Enter Base PIN” is
displayed. i Enter the base unit
PIN (default: “0000”). i M
L
If you forget your PIN, contact
your nearest Panasonic service
centre.
your nearest Panasonic service
centre.
L
When the handset has been
registered successfully, w stops
flashing.
registered successfully, w stops
flashing.
Note:
L
L
When you purchase an additional
handset, refer to the additional
handset’s installation manual for
registration.
handset, refer to the additional
handset’s installation manual for
registration.
Selecting a base unit
When “Auto” is selected, the handset
automatically uses any available base
unit it is registered to. When a specific
base unit is selected, the handset makes
and receives calls using that base unit
only. If the handset is out of range of that
base unit, no calls can be made.
When “Auto” is selected, the handset
automatically uses any available base
unit it is registered to. When a specific
base unit is selected, the handset makes
and receives calls using that base unit
only. If the handset is out of range of that
base unit, no calls can be made.
1
K
(centre of joystick) i N i
M
2
{V}
/{^}: “Select Base” i M
3
{V}
/{^}: Select the desired base
unit number, or “Auto”. i M
L
L
The handset starts searching for
the base unit.
the base unit.
Deregistering a handset
A handset can cancel its own
registration (or the registration of
another handset) that is stored in the
base unit. This allows the handset to end
its wireless connection with the system.
A handset can cancel its own
registration (or the registration of
another handset) that is stored in the
base unit. This allows the handset to end
its wireless connection with the system.
1
K
(centre of joystick) i ! i
M
2
{
3}{3}{5}
3
{V}
/{^}: “Deregistration” i
M
L
The numbers of all handsets
registered to the base unit are
displayed.
registered to the base unit are
displayed.
4
Select the handset(s) you want to
cancel by pressing the desired
handset number. i M
L
cancel by pressing the desired
handset number. i M
L
The selected handset number(s)
flashes.
flashes.
L
To cancel a selected handset
number, press the number again.
The number stops flashing.
number, press the number again.
The number stops flashing.
TG8301-8321FX(e-e).book Page 35 Thursday, April 3, 2008 1:04 PM