Mobotix MX-HALO-EXT Mount 仕様ガイド
The HiRes Video Company
EN
www
.mobotix.com
HiRes Video Innovations
The German company MOBOTIX AG is known as the leading pioneer in network camera technology and its
decentralized concept has made high-resolution video systems cost efficient.
decentralized concept has made high-resolution video systems cost efficient.
MOBOTIX AG • D-67722 Langmeil • Tel: +49 6302 9816-0 • Fax: +49 6302 9816-190 • info@mobotix.com
HaloMount: Quick Install
• Suitable for all sensor modules
• Inner ring can be tilted 20°
• High-quality metal design
• Design variety with five colors
1. Prepare opening
Prepare a circular opening with a diameter of
68 mm with a holesaw.
Prepare a circular opening with a diameter of
68 mm with a holesaw.
2. Attach hinged ferrite
Attach a hinged ferrite to the sensor cable (maximum
distance to the connector 10 cm).
Attach a hinged ferrite to the sensor cable (maximum
distance to the connector 10 cm).
3. Lead sensor cable through the opening
Lead the sensor cable through the opening in the
ceiling and allow it to protrude through (the longer
it extends, the easier the installation).
Lead the sensor cable through the opening in the
ceiling and allow it to protrude through (the longer
it extends, the easier the installation).
4. Loosen inner ring of the mount
Loosen the inner ring (fixed using a spring
mechanism) by gripping it from the inside and
moving it beyond the maximum tilt angle (moderate
pressure is sufficient).
Loosen the inner ring (fixed using a spring
mechanism) by gripping it from the inside and
moving it beyond the maximum tilt angle (moderate
pressure is sufficient).
5. Remove lock nut
If a lock nut is attached to the sensor module,
remove it. The lock nut is not needed for the
installation of the HaloMount.
If a lock nut is attached to the sensor module,
remove it. The lock nut is not needed for the
installation of the HaloMount.
6. Insert sensor module into inner ring
Insert the sensor module into the dismantled inner
ring of the HaloMount from behind.
Insert the sensor module into the dismantled inner
ring of the HaloMount from behind.
MX-HALO-EXT
-CM/CO/NG/PW/SW
31.764 _EN_V1_06/2013
Installation Mount For
S14D/S15D Sensor Modules
The MOBOTIX accessory
HaloMount offers the possibility to integrate the sensor modules of a FlexMount
Dual camera in an installation mount that can also be used for lighting equipment
(QR-CBC/MR16 LED Sharp Array 4/6 W). Since the sensor module can be tilted up to
20°, you can point the image center precisely on the area that is to be monitored.
Note: The HaloMount is not suited for unprotected outdoor usage.
Material: steel; inner ring: brass; surface: powder-coated or galvanized; colors: (matt
chrome/chrome/brushed nickel/white/black); installation diameter: 68 mm.
(QR-CBC/MR16 LED Sharp Array 4/6 W). Since the sensor module can be tilted up to
20°, you can point the image center precisely on the area that is to be monitored.
Note: The HaloMount is not suited for unprotected outdoor usage.
Material: steel; inner ring: brass; surface: powder-coated or galvanized; colors: (matt
chrome/chrome/brushed nickel/white/black); installation diameter: 68 mm.
Delivered Parts
1.1
1.2
Item
Number
Part Name
1.1
1
Outer ring with spring clip
1.2
1
Inner ring
w/o
image
1
Light connection cable (not
needed for sensor module)
Installation
Before installing the sensor modules, make sure that the sensor cables will reach the intended mounting
position without placing a strain on the cables. Disconnect the sensor modules from the sensor cables
before installing the modules. Cables with straight or with angled plugs can be used to connect the sensor
modules (on the camera: straight plugs only). Further information on the connectors and the installation
can be found in the S14/S15 manual.
position without placing a strain on the cables. Disconnect the sensor modules from the sensor cables
before installing the modules. Cables with straight or with angled plugs can be used to connect the sensor
modules (on the camera: straight plugs only). Further information on the connectors and the installation
can be found in the S14/S15 manual.
Max. 10 cm!
68 mm