JL Audio XD600/1v2 オーナーマニュアル
4 | JL Audio - XD600/1v2 Owner’s Manual
PRODUCT DESCRIPTION
The XD600/1v2 is a monoblock
amplifier utilizing JL Audio NexD™ high speed
switching technology to deliver outstanding
fidelity and efficiency.
switching technology to deliver outstanding
fidelity and efficiency.
The XD600/1v2 can be operated with a wide
variety of source units and system configurations.
Its frequency response is limited to the range
below 500 Hz. It is not designed for driving
midrange speakers or tweeters. Every aspect of its
operation has been optimized for low-frequency
amplification. For detailed specifications, please
refer to Appendix C (page 13).
midrange speakers or tweeters. Every aspect of its
operation has been optimized for low-frequency
amplification. For detailed specifications, please
refer to Appendix C (page 13).
TYPICAL INSTALLATION SEQUENCE
The following represents the sequence
for a typical amplifier installation, using an
aftermarket source unit or OEM Interface
processor (like the CleanSweep CL441dsp).
Additional steps and different procedures may
be required in some applications. If you have any
questions, please contact your authorized
JL Audio dealer for assistance.
aftermarket source unit or OEM Interface
processor (like the CleanSweep CL441dsp).
Additional steps and different procedures may
be required in some applications. If you have any
questions, please contact your authorized
JL Audio dealer for assistance.
1) Disconnect the negative battery post
connection and secure the disconnected cable
to prevent accidental reconnection during
installation. This step is not optional.
to prevent accidental reconnection during
installation. This step is not optional.
2) Run 4 AWG power wire from the battery
location to the amplifier mounting location,
taking care to route it in such a way that it will
not be damaged and will not interfere with
vehicle operation. Use 4 AWG or larger power
wire and a fused power distribution block if
additional amplifiers are being installed with
the XD600/1v2.
taking care to route it in such a way that it will
not be damaged and will not interfere with
vehicle operation. Use 4 AWG or larger power
wire and a fused power distribution block if
additional amplifiers are being installed with
the XD600/1v2.
3) Connect the power wire to the positive battery
post. Fuse the wire with an appropriate fuse
block (and connectors) within 18 inches (45
cm) wire length of the positive battery post.
This fuse is essential to protect the vehicle.
Do not install the fuse until the power wire
has been securely connected to the amplifier.
block (and connectors) within 18 inches (45
cm) wire length of the positive battery post.
This fuse is essential to protect the vehicle.
Do not install the fuse until the power wire
has been securely connected to the amplifier.
4) Run signal cables and remote turn-on wire
from the source unit to the final amplifier
mounting location.
mounting location.
5)
Run speaker cables from the speaker systems
to the amplifier mounting location.
to the amplifier mounting location.
6) Find a good, solid metal grounding point
close to the amplifier and connect the
negative power wire to it using appropriate
hardware (use of the JL Audio ECS master
ground lug, XB-MGLU is recommended). Use
4 AWG wire, no longer than 36 inches (90 cm)
from the amplifier to the ground connection
point. In some vehicles, it may be necessary to
upgrade the battery ground wire. (See page 5
for important notice).
negative power wire to it using appropriate
hardware (use of the JL Audio ECS master
ground lug, XB-MGLU is recommended). Use
4 AWG wire, no longer than 36 inches (90 cm)
from the amplifier to the ground connection
point. In some vehicles, it may be necessary to
upgrade the battery ground wire. (See page 5
for important notice).
7) Securely mount the amplifier.
8) Connect the positive and negative
8) Connect the positive and negative
power wires to the amplifier. A fuse
near the amplifier is not necessary if
the XD600/1v2 is the only device being
run from the fused main power wire.
If the fused main power wire is shared
by the XD600/1v2 and other amplifiers
or devices, fuse each amplifier/device
within 12 inches (30 cm) of wire length,
via a fused distribution block or multiple
individual fuse blocks/on-board fuses.
near the amplifier is not necessary if
the XD600/1v2 is the only device being
run from the fused main power wire.
If the fused main power wire is shared
by the XD600/1v2 and other amplifiers
or devices, fuse each amplifier/device
within 12 inches (30 cm) of wire length,
via a fused distribution block or multiple
individual fuse blocks/on-board fuses.
9) Connect the remote turn-on wire to the
amplifier or configure the “Turn-On Mode”
switch for automatic turn-on.
switch for automatic turn-on.
10) Connect the input cables to the amplifier.
11) Connect the speaker cables to the amplifier.
12) Carefully review the amplifier’s control
11) Connect the speaker cables to the amplifier.
12) Carefully review the amplifier’s control
settings to make sure that they are set
according to the needs of the system.
according to the needs of the system.
13) Install the power wire fuse (50A for a single
XD600/1v2) and reconnect the negative
battery post terminal. Install the fuse (50A)
near the amplifier (if applicable).
battery post terminal. Install the fuse (50A)
near the amplifier (if applicable).
14) Turn on the source unit at a low level to
double-check that the amplifier is configured
correctly. Resist the temptation to crank it up
until you have verified the control settings.
correctly. Resist the temptation to crank it up
until you have verified the control settings.
15) Make necessary adjustments to the
input sensitivity controls to obtain the
right overall output and the desired
balance in the system. See Appendix
A (page 12) for the recommended
input sensitivity setting method.
right overall output and the desired
balance in the system. See Appendix
A (page 12) for the recommended
input sensitivity setting method.
16) Enjoy the fruits of your labor with your
favorite music.