Q-Logic Q-Forms Kick Panel Enclosures オーナーマニュアル
1 YEAR LIMITED WARRANTY
Ai Research warrants to the original retail purchaser, this product to be free from defective workmanship and material when used under normal conditions in accordance with the product’s
printed instructions for a period of one (1) year from date of purchase. Ai Research agrees to remedy any such defect or to furnish a new part in exchange for the defective one at no charge for
parts or labor.
printed instructions for a period of one (1) year from date of purchase. Ai Research agrees to remedy any such defect or to furnish a new part in exchange for the defective one at no charge for
parts or labor.
This warranty is limited to Ai Research products and specifically excludes consequential damage to other associated equipment which may result for any reason from use with this product. In no event
shall Ai Research be liable for incidental or consequential damages or have any liability with respect to defects other than the obligations set forth above. Some states do not allow limitations on how long
an implied warranty lasts, and/or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific rights and
you may also have other rights which vary from state to state.
shall Ai Research be liable for incidental or consequential damages or have any liability with respect to defects other than the obligations set forth above. Some states do not allow limitations on how long
an implied warranty lasts, and/or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific rights and
you may also have other rights which vary from state to state.
This warranty does not cover the following:
• Damages caused by water, neglect, abuse, misuse, improper installation or operation.
• Damages caused by acts of God or nature.
• Damages occurring during shipment of the product to Ai Research for repairs.
• Any product which is modified without consent of Ai
• Damages caused by acts of God or nature.
• Damages occurring during shipment of the product to Ai Research for repairs.
• Any product which is modified without consent of Ai
Research.
QL-K1203
FACTORY KICKPANEL REMOVAL:
DRIVER Side:
Remove the hood release lever by rotating the lever up until the hood latch releases. Hold the lever in this position and gently pry out the black plastic
retaining clip on the backside of it with a small flat screwdriver. Remove the Torx head screw from the top of the dead pedal and save for re-installation
later. Remove the plastic screw cap behind the hood release lever to expose the plastic screw beneath it. Remove the plastic screw and the plastic
insert. Save the cap, screw, and insert for re-installation later. Pull the factory kick panel away from the metal bulkhead releasing snap clips. Slide the
dead pedal upward toward the bottom of the dash and then pull away from floorboard. Make sure all of the snap clips are removed from the metal
bulkhead.
Remove the hood release lever by rotating the lever up until the hood latch releases. Hold the lever in this position and gently pry out the black plastic
retaining clip on the backside of it with a small flat screwdriver. Remove the Torx head screw from the top of the dead pedal and save for re-installation
later. Remove the plastic screw cap behind the hood release lever to expose the plastic screw beneath it. Remove the plastic screw and the plastic
insert. Save the cap, screw, and insert for re-installation later. Pull the factory kick panel away from the metal bulkhead releasing snap clips. Slide the
dead pedal upward toward the bottom of the dash and then pull away from floorboard. Make sure all of the snap clips are removed from the metal
bulkhead.
PASSENGER Side:
Pull the factory kick panel away from the metal bulkhead releasing snap clips. . Make sure all of the snap clips are removed from the metal bulkhead.
Pull the factory kick panel away from the metal bulkhead releasing snap clips. . Make sure all of the snap clips are removed from the metal bulkhead.
Note:
Always check the fit of the Q-Forms panel in the vehicle BEFORE any cutting or modifications are done!
SPEAKER INSTALLATION:
Cut the speaker holes in the Q-Forms before installing the panels in the vehicle. Using a hole saw of the correct size, position the pilot drill on the dimple
at the center of the speaker mounting surface. Be careful as the hole saw exits the rear of the panel. Install speaker wiring and crossover network as
per manufacture’s instructions. Install tweeters as per manufacture’s instructions. Install midrange drivers after Q-Forms panels have been installed in
the vehicle.
at the center of the speaker mounting surface. Be careful as the hole saw exits the rear of the panel. Install speaker wiring and crossover network as
per manufacture’s instructions. Install tweeters as per manufacture’s instructions. Install midrange drivers after Q-Forms panels have been installed in
the vehicle.
Q-FORMS KICKPANEL INSTALLATION:
DRIVER’S Side:
Lay the Q-Forms kick panel into place in the approximate location and connect the speaker wiring. Install the kick
panel into the permanent position previously held by the original kick panel. Be sure that the front edge of the panel
fits tightly against the rubber door seal. Secure the panel by reinstalling the Torx screw removed earlier, into the
predrilled hole in the recessed area at the top of the Q-Forms panel. Re-install the square plastic insert, plastic screw
and cover behind the hood release lever making sure that it is oriented correctly to be received by the square hole in
the metal behind the kick panel. Press the panel firmly down against the carpet. Further secure the panel by drilling a
1/8” pilot hole into the metal behind the panel using the pre-drilled hole in the panel below the midrange and tweeter as
a guide. Secure using the supplied 2” pan-head screw. Drive screw through the carpet and into the predrilled hole in
the metal floor pan. Lay the supplied polyfill in and around the opening for the midrange driver. Install the
midrange driver as per manufacture’s instructions. Be sure to center driver in opening to allow clearance for the
speaker grill.
Lay the Q-Forms kick panel into place in the approximate location and connect the speaker wiring. Install the kick
panel into the permanent position previously held by the original kick panel. Be sure that the front edge of the panel
fits tightly against the rubber door seal. Secure the panel by reinstalling the Torx screw removed earlier, into the
predrilled hole in the recessed area at the top of the Q-Forms panel. Re-install the square plastic insert, plastic screw
and cover behind the hood release lever making sure that it is oriented correctly to be received by the square hole in
the metal behind the kick panel. Press the panel firmly down against the carpet. Further secure the panel by drilling a
1/8” pilot hole into the metal behind the panel using the pre-drilled hole in the panel below the midrange and tweeter as
a guide. Secure using the supplied 2” pan-head screw. Drive screw through the carpet and into the predrilled hole in
the metal floor pan. Lay the supplied polyfill in and around the opening for the midrange driver. Install the
midrange driver as per manufacture’s instructions. Be sure to center driver in opening to allow clearance for the
speaker grill.
PASSENGER’S Side:
Lay the Q-Forms kick panel into place in the approximate location and connect the speaker wiring. Install the kick
panel into the permanent position previously held by the original kick panel. Be sure that the front edge of the
panel fits tightly against the rubber door seal. Slide the panel up until it is about 1/8” from the bottom of the dash.
Press the panel firmly down against the carpet. Drill a 1/8” pilot hole into the metal behind the panel using the
pre-drilled hole in the panel below the midrange and tweeter as a guide. Secure using the supplied 3” pan-head
screw. Drive screw through the carpet and into the predrilled hole in the metal floor pan. Lay the supplied polyfill
in and around the opening for the midrange driver. Install the midrange driver as per manufacture’s instructions.
Be sure to center driver in opening to allow clearance for the speaker grill.
Lay the Q-Forms kick panel into place in the approximate location and connect the speaker wiring. Install the kick
panel into the permanent position previously held by the original kick panel. Be sure that the front edge of the
panel fits tightly against the rubber door seal. Slide the panel up until it is about 1/8” from the bottom of the dash.
Press the panel firmly down against the carpet. Drill a 1/8” pilot hole into the metal behind the panel using the
pre-drilled hole in the panel below the midrange and tweeter as a guide. Secure using the supplied 3” pan-head
screw. Drive screw through the carpet and into the predrilled hole in the metal floor pan. Lay the supplied polyfill
in and around the opening for the midrange driver. Install the midrange driver as per manufacture’s instructions.
Be sure to center driver in opening to allow clearance for the speaker grill.
Installation of your new Q-Forms kick panels is complete.
Start enjoying your front row - center stage seats!
Before
After
Supplied Hardware:
1 - #8 x 2” panhead sheet metal screw
1 - #8 x 3” panhead sheet metal screw
40” - Rubber U-channel
2 - 6” x 8” Polyfill Pad
2 - Color matched grills
1 - #8 x 2” panhead sheet metal screw
1 - #8 x 3” panhead sheet metal screw
40” - Rubber U-channel
2 - 6” x 8” Polyfill Pad
2 - Color matched grills
1998-up Volkswagen Beetle
INSTALL GRILLS:
Cut the supplied rubber U-channel in half (approximately 20” each). Apply rubber U-channel around the edge of
the grill, trim excess U-channel if needed and press grill into the grill opening in the Q-Forms panel.
Cut the supplied rubber U-channel in half (approximately 20” each). Apply rubber U-channel around the edge of
the grill, trim excess U-channel if needed and press grill into the grill opening in the Q-Forms panel.