Q-Logic Q-Forms Kick Panel Enclosures オーナーマニュアル
QL-K6001
Honda Civic / CRX 1988-1991
Remove Original Kick Panel
• On driver's side unbolt two 10mm bolts used to attach hood release. Detach christmas tree clip
attaching kick panel.
• On passenger's side detach christmas tree clips attaching kick panel.
• Remove threshold plate by prying directly upward.
• Remove clips which attach the bottom of the threshold plate assembly and carpet.
• Cut kick panel away from threshold plate one inch forward of wide section.
• Remove threshold plate by prying directly upward.
• Remove clips which attach the bottom of the threshold plate assembly and carpet.
• Cut kick panel away from threshold plate one inch forward of wide section.
NOTE: Always check the fit of the Q-Forms into the vehicle before any cutting or modifications are done.
Install Speakers
• Cut the speaker holes into the Q-Forms before installing them into the vehicle.
• Install the speakers into the Q-Forms after they have been installed into the vehicle.
• Install speaker wiring and crossover network as per manufacturer’s instructions.
• Using a hole saw of correct size, position pilot drill on dimple at center of speaker mounting surface.
A die grinder or keyhole saw may also be used.
• Lay the supplied polyfill in and around the Q-forms cavity behind the speakers.
• Cut speaker mounting holes taking care as saw exits rear of panel.
• Secure speakers into locations by driving screws through speaker bezel and into mounting surface.
• Install the speakers into the Q-Forms after they have been installed into the vehicle.
• Install speaker wiring and crossover network as per manufacturer’s instructions.
• Using a hole saw of correct size, position pilot drill on dimple at center of speaker mounting surface.
A die grinder or keyhole saw may also be used.
• Lay the supplied polyfill in and around the Q-forms cavity behind the speakers.
• Cut speaker mounting holes taking care as saw exits rear of panel.
• Secure speakers into locations by driving screws through speaker bezel and into mounting surface.
Be careful to center speakers in mounting surface to allow clearance for grill shell.
• Install tweeters as per manufacturer’s instructions.
Install New Q-Forms Kick Panels (Always predrill all mounting screw locations)
• Reattach only the top 10mm bolt and hood release. Twist hood release back towards door jam so that
the lever is straight up and down. Drive large 1" truss head into bulk head metal through lower
mounting hole of hood release.
mounting hole of hood release.
• Install supplied welt to exposed metal edge.
• Lay Q-forms kick panel in approximate location and connect speaker wiring.
• Install panel into permanent position previously held by original kick panel. Be sure front
• Lay Q-forms kick panel in approximate location and connect speaker wiring.
• Install panel into permanent position previously held by original kick panel. Be sure front
edge of panel fits tightly against welt.
• Reinstall threshold plate by pushing clips into original slots.
• On driver's side install supplied 3 inch screw and 2 1/2 inch spacer at hole in top rear
• On driver's side install supplied 3 inch screw and 2 1/2 inch spacer at hole in top rear
panel edge. Drive into bulkhead sheet metal.
• Secure driver's and passenger's side upper front edge with 1 inch
sheet metal screw provided.
• Secure passenger's side in web between speakers at lower edge,
using 3 inch sheet metal screw and 2 1/2 inch spacer provided.
• It may be helpful to predrill screw pilot holes if installed without power tools.
• Install grill shells by pressing snugly into woofer cavity.
• Install grill shells by pressing snugly into woofer cavity.
QL-K6001 Included Hardware:
(2) 3" sheet metal screws
(2) 2 1/2" plastic spacers
(2) 1" sheet metal screws
(2) 6" x 8" polyfill pieces
(2) 6.25" Q-grills
(2) 2 1/2" plastic spacers
(2) 1" sheet metal screws
(2) 6" x 8" polyfill pieces
(2) 6.25" Q-grills
Estimated Installation Time: 1.5 Hrs.
inst ver 51.1