Q-Logic Q-Forms Kick Panel Enclosures オーナーマニュアル

7/17/00

FACTORY KICKPANEL REMOVAL:
     DRIVER Side:

Remove threshold panel along the bottom of the door opening by prying up to release snap clips.  Pull the factory kick panel away from the

metal bulkhead releasing snap clips.  Make sure all of the snap clips are removed from the metal bulkhead.  Remove the (2) 10mm bolts that retain
the factory dead pedal.  Pull back the carpet and remove the (2) 12mm bolts and (1) 10mm nut that retain the dead pedal mounting bracket.  Remove
the bracket and press the carpet down firmly against the floor pan.
     PASSENGER Side:

Remove threshold panel along the bottom of the door opening by prying up to release snap clips.  Pull the factory kick panel away from the

metal bulkhead releasing snap clips.
Note:  Always check the fit of the Q-Forms panel in the vehicle BEFORE any cutting or modifications are done!
SPEAKER INSTALLATION:

Cut the speaker holes in the Q-Forms before installing the panels in the vehicle.  Using a hole saw of the correct size, position the pilot drill

on the dimple at the center of the speaker mounting surface.  Be careful as the hole saw exits the rear of the panel.  Install speaker wiring and
crossover network as per manufacture’s instructions.  Install tweeters as per manufacture’s instructions.  Install midrange drivers after Q-Forms
panels have been installed in the vehicle.
Q-FORMS KICKPANEL INSTALLATION:
     DRIVER’S Side:

Lay the Q-Forms kick panel into place in the approximate location and connect the speaker wiring.  Install the kick panel into the permanent

position previously held by the original kick panel.  Be sure that the front edge of the panel fits tightly against the rubber door seal.  Slide the panel up
until it meets the bottom of the dash.  Re-install the threshold panel along the bottom of the door opening.  Press the panel firmly down against the
carpet.  Drill a 1/8” pilot hole into the metal behind the panel using the pre-drilled hole in the panel behind the hood release as a guide.  Secure using
the supplied 1” truss head screw.  Continue to apply downward pressure while installing the supplied 3” Pan head sheet metal screw through the pre-
drilled hole in the bottom of the panel.  Drive screw through the carpet and into the metal floor pan.  Lay the supplied polyfill in and around the
opening for the midrange driver.  Install the midrange driver as per manufacture’s instructions.  Be sure to center driver in opening to allow clearance
for the speaker grill.
     Simulated Dead Pedal Installation:
             Position the supplied “dead pedal” with the angled edge against the bottom of the Q-Forms Kickpanel.  Center the panel over the hole in the
carpet and secure with the supplied 2 1/2” Pan head sheet metal screw.  

Do not over tighten!

     PASSENGER’S Side:

Lay the Q-Forms kick panel into place in the approximate location and connect the speaker wiring.  Install the kick panel into the permanent

position previously held by the original kick panel.  Be sure that the front edge of the panel fits tightly against the rubber door seal.  Slide the panel up
until it meets the bottom of the dash.  Re-install the threshold panel along the bottom of the door opening.  Drill a 1/8” pilot hole into the metal behind
the panel using the pre-drilled hole in the top of the panel as a guide.  Install the supplied 1 1/2” pan head screw through the panel, through the
supplied 1” nylon spacer and into the previously drilled hole in the metal.  Continue to apply downward pressure to the panel and install the 3” pan
head sheet metal screw through the pre-drilled hole in the bottom of the panel.  Drive the screw through the carpet and into the metal floor pan.  Lay
the supplied polyfill in and around the opening for the midrange driver.  Install the midrange driver as per manufacture’s instructions.  Be sure to
center driver in opening to allow clearance for the speaker grill.
INSTALL GRILLS:

Cut the supplied rubber U-channel in half (approximately 20” each”) Apply rubber U-channel around the edge of the grill, trim excess U-

channel if needed and press grill into the grill opening in the Q-Forms panel.

Supplied Hardware:

1  -  #8 x 1” Truss head SMS
1  -  #8 x 1.5” SMS
1  -  1” Nylon Spacer
2  -  3” Pan head SMS
1  -  2 1/2” Pan head SMS

         40”  -  Rubber U-channel

2  -  6” x 8” Polyfill Pad

2  -  Color matched grills